【单选题】
间隙激振引起的自激振荡的主要特点是___。
A. 与电网频率有关;
B. 与电网频率无关;
C. 与机组的负荷无关;
D. 与机组的负荷有关。
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
D
解析
暂无解析
相关试题
【单选题】
汽轮机的负荷摆动值与调速系统的迟缓率___。
A. 成正比;
B. 成反比;
C. 成非线性关系;
D. 无关。
【单选题】
当转子的临界转速低于工作转速___时,才有可能发生油膜振荡现象。
A. 4/5;
B. 3/4;
C. 2/3;
D. 1/2。
【单选题】
滑参数停机时,___作汽轮机超速试验。
A. 可以;
B. 采取安全措施后;
C. 严禁;
D. 领导批准后。
【单选题】
滑参数停机过程与额定参数停机过程相比,___。
A. 容量出现正胀差;
B. 容易出现负胀差;
C. 胀差不会变化;
D. 胀差变化不大。
【单选题】
汽轮机停机惰走降速时,由于鼓风作用和泊桑效应,低压转子会出现___突增。
A. 正胀差;
B. 负胀差;
C. 不会出现;
D. 胀差突变。
【单选题】
机组变压运行,在负荷变动时,要___高温部件温度的变化。
A. 减少;
B. 增加;
C. 不会变化;
D. 剧烈变化。
【单选题】
蒸汽与金属间的传热量越大,金属部件内部引起的温差就___。
A. 越小;
B. 越大;
C. 不变;
D. 少有变化。
【单选题】
汽轮机在稳定工况下运行时,汽缸和转子的热应力___。
A. 趋近于零;
B. 趋近于某一定值;
C. 汽缸大于转子;
D. 转子大于汽缸。
【单选题】
新装机组的轴承振动不宜大于___mm。
A. 0.045;
B. 0.040;
C. 0.035;
D. 0.030。
【单选题】
给水泵在运行中的振幅不允许超过0.05mm,是为了___。
A. 防止振动过大,引起给水压力降低;
B. 防止振动过大,引起基础松动;
C. 防止轴承外壳遭受破坏;
D. 防止泵轴弯曲或轴承油膜破坏造成轴瓦烧毁。
【单选题】
当凝汽器真空度降低,机组负荷不变时,轴向推力___。
A. 增加;
B. 减小;
C. 不变;
D. 不确定。
【单选题】
当___发生故障时,协调控制系统的迫降功能将使机组负荷自动下降到50%MCR或某一设定值。
A. 主设备;
B. 机组辅机;
C. 发电机;
D. 锅炉。
【单选题】
两班制调峰运行方式为保持汽轮机较高的金属温度,应采用___。
A. 滑参数停机方式;
B. 额定参数停机方式;
C. 定温滑压停机方式;
D. 任意方式。
【单选题】
汽轮机发生水冲击时,导致轴向推力急剧增大的原因是___。
A. 蒸汽中携带的大量水分撞击叶轮;
B. 蒸汽中携带的大量水分引起动叶的反动度增大;
C. 蒸汽中携带的大量水分使蒸汽流量增大;
D. 蒸汽中携带的大量水分形成水塞叶片汽道现象。
【单选题】
汽轮发电机的振动水平是用___来表示的。
A. 基础的振动值;
B. 汽缸的振动值;
C. 地对轴承座的振动值;
D. 轴承和轴颈的振动值。
【单选题】
机组频繁启停增加寿命损耗的原因是___。
A. 上下缸温差可能引起动静部分摩擦;
B. 胀差过大;
C. 汽轮机转子交变应力太大;
D. 热应力引起的金属材料疲劳损伤。
【单选题】
国产300、600MW汽轮机参加负荷调节时,机组的热耗表现为___。
A. 纯变压运行比定压运行节流调节高;
B. 三阀全开复合变压运行比纯变压运行高;
C. 定压运行喷嘴调节比定压运行节流调节低;
D. 变压运行最低。
【单选题】
汽轮机变工况运行时,蒸汽温度变化率愈( ),转子的寿命消耗愈___。
A. 大、大;
B. 大、小;
C. 小、大;
D. 寿命损耗与温度变化没有关系。
【单选题】
作真空系统严密性试验时,如果凝汽器真空下降过快或凝汽器真空值低于___MPa,应立即开启抽气器空气泵,停止试验。
A. 0.09;
B. 0.087;
C. 0.084;
D. 0.081。
【单选题】
数字式电液控制系统用作协调控制系统中的___部分。
A. 汽轮机执行器;
B. 锅炉执行器;
C. 发电机执行器;
D. 协调指示执行器。
【单选题】
根据环境保护的有关规定,机房噪声一般不超过___dB。
A. 80~85;
B. 85~90;
C. 90~95;
D. 95~100。
【单选题】
为了防止油系统失火,油系统管道、阀门、接头、法兰等附件承压等级应按耐压试验压力选用,一般为工作压力的___倍。
A. 1.5;
B. 1.8;
C. 2;
D. 2.2。
【单选题】
中间再热机组应该___进行一次高压主汽门、中压主汽门(中压联合汽门)关闭试验。
A. 隔天;
B. 每周;
C. 隔10天;
D. 每两周。
【单选题】
机组启动前,发现任何一台油泵或其自启动装置有故障时,应该___。
A. 边启动边抢修;
B. 切换备用油泵;
C. 报告上级;
D. 禁止启动。
【多选题】
运行中通过监视调节级压力的变化可以判断___
A. 新蒸汽流量的变化,负荷的高低;
B. 通流部分是否存在结垢、损坏及堵塞
C. 汽轮机叶片是否损坏、变形;
D. 主蒸汽压力的变化;
【多选题】
汽轮机通流部分结垢后,可导致___
A. 汽轮机接带负荷的能力下降;
B. 汽轮机的效率降低;
C. 汽轮机级的反动度发生变化;
D. 汽轮机的轴向推力增加;
【多选题】
汽轮机发生过大的振动时存在哪些危害___
A. 损坏机组零件;
B. 动静部分发生摩擦;
C. 造成基础松动或周围建筑物损坏;
D. 造成汽缸变形;
【多选题】
汽轮机运行中发生振动,可能的原因有___
A. 主汽温度过低或轴封带水发生水冲击;
B. 汽缸变形、滑销系统卡涩导致动静部分摩擦;
C. 汽轮机组转子弯曲、中心不正或叶片脱落;
D. 油质恶化有杂物、油压过低或油温过高;
【多选题】
运行中给水温度下降的原因有___
A. 高加换热管结垢、堵管较多或机组负荷下降;
B. 高加换热管发生泄漏;
C. 高加液位过高或水侧流量突然增加;
D. 高加内部隔板泄漏或水侧旁路未关严;
【多选题】
由工业冷却水供给密封水或冷却水的设备有___
A. 给水泵、凝结泵、真空泵冷却水;
B. 润滑油冷油器、EH油冷油器和发电机空冷器;
C. 给水泵、凝结泵密封水;
D. 润滑油油净化装置真空泵;
【多选题】
向辅汽母管供汽的汽源有___
A. 两台机的三段抽汽;
B. 两台辅汽减温减压器;
C. 化工区来启动汽源;
D. 除氧器汽平衡母管;
【多选题】
汽轮机启动前高压启动油泵供___系统用油。
A. 各轴承冷却油;
B. 调速系统附加保安油;
C. 调速系统保安油;
D. 汽轮机挂闸油;
【多选题】
机组正常运行中定期工作涉及的内容大致可分为___几类
A. 运行设备与备用设备的定期切换或联锁试验;
B. 各容器液位保护的定期试验;
C. 汽轮机本体或重要辅助设备性能试验;
D. 各转动设备测振及油质检查;
【多选题】
汽轮机排汽装置漏入空气表现为___
A. 汽轮机真空偏低;
B. 机组真空严密性降低;
C. 凝结水过冷度增加;
D. 凝结水含氧量升高;
【多选题】
辅机启动前检查项目有___
A. 检修工作结束,工作票收回,检修杂物已清理
B. 手动盘车灵活无卡涩,启动前无倒转现象;
C. 各润滑部位油质、油位、油温正常,冷却水正常
D. 转向正确,绝缘合格
【多选题】
转动设备所处的状态有___
A. 检修
B. 运行
C. 紧急备用
D. 备用
【多选题】
辅机启动后的检查项目有___
A. 轴承温度、振动合格,窜轴≯2-4mm;
B. 电动机温升、电流正常,无异音;
C. 辅机密封水、冷却水、润滑油无泄漏;
D. 装置机械、系统连接正常,处理正常;
【多选题】
工业冷却水DLS型滤水器的反洗方式有___
A. 手动反冲洗
B. 定时反冲洗
C. 底部排污反冲洗
D. 自动反冲洗
【多选题】
顶轴油压低的原因有___
A. 顶轴油泵入口压力低或入口滤网堵塞;
B. 顶轴油泵旁通阀误开或开度过大;
C. 安全阀整定不当;
D. 顶轴油泵出入口阀开启不够;
【多选题】
运行中EH油母管压力下降的原因有___
A. EH油泵出、入口滤网堵塞;
B. EH油系统泄漏;
C. EH油泵跳闸或变量机构故障;
D. EH油系统安全溢油阀失灵;
推荐试题
【单选题】
Fuel______means the quantity of fuel carried by now. ___
A. reminding
B. endurance
C. number
D. total
【单选题】
The opposite meaning of“speedup”is_________
A. slowdown
B. speeddown
C. speedlow
D. slowby
【单选题】
Pilot turns on squawk______to request a squawk number. ___
A. 3000
B. 3500
C. 4000
D. 2000
【单选题】
First______assistance means doctor and ambulance in an emergency condition. ___
A. emergency
B. priority
C. aid
D. help
【单选题】
When somebody is reported hurt on board,maybe it will need______assistance on arrival. ___
A. fire-cart
B. medical
C. police
D. wheelchair
【单选题】
In emergency descent procedure,the pilot should turn right______out of the route while descending. ___
A. 40°
B. 30°
C. 20器
D. 15°
【单选题】
管制员在对空指挥过程中,越是繁忙的时候,语速应___
A. 保持平稳,避免频繁重复指令
B. 尽量快些,才能指挥更多飞机
C. 降低语速,避免口误
D. 时快时慢,引起机组的注意
【单选题】
According to ICAO,a standard holding pattern should all turn to the______.___
A. right
B. west
C. left
D. east
【单选题】
The standard altimeter setting is______inhpa. ___
A. 1013.20062
B. 1010.10062
C. 29.92002
D. 30.10002
【单选题】
2500f/m rate of vertical speed is equal to______.___
A. 10m/s
B. 15m/s
C. 20m/s
D. 25m/s
【单选题】
陆空通话时,什么时候推荐使用“IMMEDIATELY(立即)”这个词:___
A. 相对飞行穿高度时
B. 天气差时,担心自己会忘记某个正在改变高度的动态
C. 飞机多时,为了节省精力
D. 在紧急情况下,用于冲突解脱时
【单选题】
Standard rate for a turning is______degrees per second. ___
A. 4
B. 6
C. 3
D. 2
【单选题】
What is the best course of action for a pilot to follow when thunderstorms are observed along the route of flight? ___
A. Fly below the thunderstorms
B. Climb over the thunderstorms
C. Disregard the thunderstorms
D. Take any action to avoid all thunderstorms
【单选题】
The subdivision of frequencies is______MHZ. ___
A. 0.025
B. 0.035
C. 0.02
D. 0.015
【单选题】
Aeronautical chart is divided into two categories,______. ___
A. Aeronautical map and special type of aeronautical chart
B. En-route chart and approach chart
C. Area chart and standard instrument arrival and departure chart
D. Aerodrome chart and area chart
【单选题】
Aircraft are required to comply with ATC instructions within______.___
A. advisory airspace
B. domestic airspace
C. controlled airspace
D. international airspace
【单选题】
Amendments to the initial clearance will be issued at anytime an air traffic controller deems such action necessary to______.___
A. avoid possible confliction between aircraft
B. correct the previously issued clearance
C. cancel the flight plan
D. expedite the traffic
【单选题】
研究表明,当耳机话筒的位置距离嘴( )英寸且稍微偏下时,传输的声音质量最佳。(注:1英寸=2.54CM)___
A. 0.25-0.5
B. 0.75-1
C. 1.25-1.5
D. 1.75-2
【单选题】
“I want to divert to shanghai” is equal to______.___
A. I want to our destination Shanghai
B. I want to overfly Shanghai
C. I want to alternate to land at Shanghai
D. I want to call Shanghai control
【单选题】
When an aircraft is being subjected to unlawful interference, the pilot should try to notify _______ of this fact.___
A. the appropriate ATC units
B. company
C. the passengers on board
D. air attendants
【单选题】
When pilot say“Did you pick it upon your screen?”,that means______.___
A. did you pick up your screen?
B. did you see it on your screen?
C. did your screen pick me up?
D. did you change your radar?
【单选题】
ATC clearance does not contain______.___
A. clearance limit
B. altitude data
C. route of flight
D. flight direction
【单选题】
When pilot sets an altimeter setting to a QNH,that will indicate_________
A. flight level
B. altitude
C. height
D. safety level
【单选题】
When pilots set a pressure of 29.92 in mercury to indicate_________
A. altitude
B. height
C. flight level
D. safety level
【单选题】
管制员还应当对管制指令当中的不同内容进行适当的排序,相对重要的内容应当排列在管制指令的 ( )位置___
A. 前面
B. 中间
C. 尾部
D. 以上都可以
【单选题】
When Beijing time is 0801,Zulu time should be______.___
A. 2001
B. 1
C. 601
D. 1601
【单选题】
Emergency frequency is______.___
A. 121.5MHZ
B. 120.5MHZ
C. 121MHZ
D. 119.0MHZ
【单选题】
“PAN” is the international RTF______signal___
A. emergency
B. distress
C. urgency
D. dangerous
【单选题】
“MAYDAY” is the international RTF______signal.___
A. emergency
B. distress
C. urgency
D. dangerous
【单选题】
According to ICAO definition, a condition concerning the safety of an aircraft or other vehicle or of some person on board or within sight but which does not require immediate assistance is _______ .___
A. urgency
B. dangerous
C. emergency
D. distress
【单选题】
Which SSR Code is not right?___
A. 7020
B. 8025
C. 6060
D. 4021
【单选题】
______is the accepted standard for worldwide time signal broadcast used for aviation.___
A. GMT
B. LT
C. UTC
D. SST
【单选题】
_____means the level is measured in 1013.2 pha___
A. Level
B. Height
C. Altitude
D. Flight level
【单选题】
An aircraft known or believed to be in a state of emergency should be given______over other aircraft.___
A. way
B. flight plan
C. instruction
D. priority
【单选题】
管制话筒正确使用方法是:___
A. PTT发射键还没有完全按下时就开始发指令
B. 指令还没有结束就松开PTT发射键
C. 按PTT发射键与发话同时进行,松开PTT发射键与发话同时进行
D. 先按下话筒PTT发射键,然后再开始对空发话,发话完毕后再松开话筒PTT发射键
【单选题】
SSR code is a______digital number.___
A. two
B. six
C. one
D. four
【单选题】
Traffic information should include_________
A. direction of aircraft concerned
B. weather
C. speed of aircraft
D. heading of aircraft
【单选题】
根据区管中心业务通告,管制员通知机组转换频率的管制指令应当与其他管制指令( )。___
A. 分开发布
B. 同时发布
C. 无特别要求
【单选题】
20NM is equal to.___
A. 40km
B. 38km
C. 37km
D. 41km
【单选题】
The altimeter setting used in en-route flight should be______hpa___
A. 1019
B. 1013
C. 2992
D. 1000