【单选题】
有一台笔记本电脑出现一个故障现象该故障发生在主板上故障概率是50%发生在内存上的故障概率是30%针对这个故障有一个技术通报是针对硬盘的。你要对这台电脑用替换法排除故障那么___
A. 这台笔记本电脑的硬盘不是通报中所说的所以不更换硬盘
B. 先更换主板测试
C. 更换主板和内存
D. 这些部件都要更换
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
B
解析
暂无解析
相关试题
【单选题】
有一台电脑不能无线上网。通过你的观察和测试你发现在设备管理器中无线网卡设备不正确(有叉号)这时你手头正好有该无线网卡的新版驱动程序。这时你会___
A. 在设备管理器中使用重新扫描设备的方法恢复无线网卡的驱动
B. 重新安装标配的无线网卡驱动程序
C. 卸载原来的无线网卡驱动安装新版的无线网卡驱动
D. 重新安装操作系统后再安装新版的无线网上驱动程序
【单选题】
用户向你反映他只要插上他的U盘电脑就会死机。你到达现场后通过观察和分析你准备使用替换法来确定故障部件。你最先替换的是___
A. 更新USB驱动
B. 用自己的好的U盘插上去测试
C. 更换主板
D. 重新安装另一操作系统
【单选题】
用户有一台电脑不能上网。你到达现场后你准备一步步测试来来排除故障。你最先考虑的是___
A. 更新网卡驱动
B. 更换网线
C. 更换主板
D. 重新插拔一下网线
【单选题】
对于一台不能加电开机的故障电脑你准备更换它的电源。在更换之前你应该___
A. 确保更换的电源是好的
B. 确保主板等部件无短路开情况(可用电脑负载仪测试故障电源是否正常输出来判断主板等是否有短路的情况)
C. 确保市电电压是正常的
D. 以上都是
【单选题】
有一用户反应他的电脑不能上网。你来到用户的家中在维修过程中你需要___
A. 首先确认网线是否插好
B. 用户反映的故障是否存在
C. 网卡是否没有安装驱动
D. 网卡是否已经损坏
【单选题】
你为用户修复了单独使用电池不能开机的现象(假设你就是为用户更换了一块电池)维修后你应检验下列哪些方面___
A. 检验单独使用电池时电池是否正常放电
B. 检查电池能否中正常地充电
C. 使用电池单独开机开机过程是否正常
D. 以上都是
【多选题】
硬件最小系统法需要那些硬件?___
A. 电源
B. 主板
C. CPU(带风扇)
D. 网卡
E. 显示器
【多选题】
静电是如何产生的方式?___
A. 摩擦起电
B. 感应起电
C. 连接起电
D. 接触分离起电
【多选题】
静电的基本物理特性为___
A. 摩擦起电
B. 感应起电
C. 连接起电
D. 接触分离起电
【多选题】
静电的基本三种物理特性能对电子元件的影响有以下几种___
A. 静电吸附灰尘降低元件绝缘电阻(缩短寿命)
B. 静电放电破坏使元件受损不能工作(完全破坏)
C. 静电放电电场或电流产生的热使元件受伤(潜在损伤)。
D. 以上都不对
【多选题】
静电危害的特性___
A. 隐蔽性
B. 潜在性
C. 随机性
D. 复杂性
【多选题】
标准防静电操作系统包括___
A. 防静电安全工作台
B. 防静电桌垫
C. 防静电地板
D. 防静电元件盒
E. 离子风机
F. 防静电区 域警示标志
【多选题】
雷电的传导途径___
A. 电源线缆
B. 无线信号传导
C. 信号电缆
D. 光纤传导
【多选题】
预防雷击损伤的电源隔离设备有___
A. 稳压稳流器
B. 隔离变压器
C. 避雷针
D. 接地线
【多选题】
技术规范主要环节定义___
A. 维修前
B. 维修中
C. 维修完毕
D. 客户取机
【多选题】
维修前的准备工作包括___
A. 工具准备
B. 外观检查
C. 市电检测
D. 静电防护
E. 释放电荷
F. 电池操作
【多选题】
常见维修工具___
A. 防静电手环
B. 防静电桌垫
C. 螺丝盒
D. 小十字螺丝刀
E. 镊子
【多选题】
电源线包括哪三项___
A. 火线
B. 地线
C. 零线
D. 电线
【多选题】
电池操作的注意事项___
A. 断开电源适配器
B. 取下电池并摆放好
C. 注意防潮和正负极不短路
D. 以上都不对
【多选题】
工具选择规范操作标准___
A. 不同的螺丝需根据规格对应使用不同的螺丝刀严禁出现一把螺丝刀通吃的现象;
B. 插头类线材拆装需借助起拔器严禁用手直接拔线;
C. 扁平类线材拆装需借助镊子严禁用手直接拔线;
D. 盖板类拆装时如果需要一字螺丝刀辅助必须在一字螺丝刀的刀头贴胶布防止出现划伤。
【多选题】
规范操作注意事项___
A. 拆装时需小心谨慎
B. 根据部件特点、注意部件本身要求。如硬盘严禁放置在强磁场附近
C. 出现错误应及时改正
D. 严禁带电拆装
【多选题】
部件摆放注意事项说法正确的是___
A. 部件须在防静电布上或盒内摆放整齐
B. 部件不能有堆叠
C. 拆下的螺丝放入螺丝盒
D. 拆下的螺丝整齐排放在防静电布上
【多选题】
台式机主电源输出的电源电压有以下几种___
A. +3.3V
B. -3.3V
C. +5V
D. -5V
E. +12V
F. -12V
【多选题】
内存更换操作规范正确的是___
A. 轻轻向外侧拨开内存槽两端的卡舌然后取下内存;
B. 拆装内存时不能够用力捏内存条上的内存颗粒;
C. 取下内存后仔细观察有无烧毁痕迹;
D. 检查金手指是否有氧化必要时使用橡皮进行清洁
【多选题】
更换CPU与CPU风扇部件外观检查正确的是___
A. –检查CPU插座附近的电容及电感是否有变形或烧坏的现象
B. 检查主板的CPU插座是否有烧毁、变色现象
C. 检查CPU插针是否有弯曲、断针情况
D. 检查CPU表面是否有烧痕、变形、破损;
E. –检查CPU风扇是否有不转、停顿及转速过低的现象;
F. 检查CPU风扇是否有扇叶断裂固定位置螺丝有无断裂。
【多选题】
LGA 775 CPU及主板操作规范正确的是___
A. 掀开金属盖后才可以取下保护盖塑料的保护盖。
B. 拆装时手指捏住CPU上下侧中间部位
C. 拆装CPU时垂直插入或者拔出
D. 不要触碰插座的触针或CPU的触板
E. 不要随意更换主板或者CPU测试判断是主板或者CPU故障后再更换。
F. 返回故障主板时必须安装CPU插座的塑料保护盖否则造成CPU插座损坏为“非损”。
【多选题】
主板检测规范注意事项正确的是___
A. 硬件最小系统法应仅保留CPU、CPU散热器、主板、电源
B. 可以根据实际情况在硬件最小化的基本部件上采用逐步添加法逐件的增加部件然后再判断具体的故障部件
C. 硬件最小系统法先在机箱内测试如果仍无法正常的启动需要将最小化的部件拿到机箱外再次确认以排除部件与机箱短路等原因造成的故障。
D. 硬件最小系统法应仅保留CPU、CPU散热器、主板、电源、显示器、键盘;
【多选题】
主板更换操作规范部件外观检查说法正确的是___
A. 检查北桥、南桥、声卡、网卡等主板集成芯片是否有变色或裂痕芯片与主板PCB连接的引脚处是否有断裂或翘起的现象;
B. 检查各连接线是否有有破损、歪针、错针、虚接、漏接、错接的现象
C. 检查主板上主要电容是否鼓起、漏液或有液体流淌锈蚀、霉变等痕迹
D. 检查主板PCB板是否有变色、腐蚀、烧穿的情况;
【多选题】
硬盘、光驱及软驱-操作规范正确的是___
A. 在拆卸故障硬盘或者光驱的数据线与电源线的时候严禁野蛮操作。
B. 对新硬盘或者光驱正确的设置跳线。
C. 安装新硬盘或者光驱正确的连接电源线与数据线。
D. 开机加电确认BIOS中硬盘或者光驱被正确的识别。
【多选题】
键盘、鼠标检验规范正确的是___
A. 检查键盘、鼠标外部连线是否破损、扭曲、非正常压迫等现象
B. 检查键盘、鼠标接头是否有断针、歪针现象。
C. USB键盘、USB鼠标需要注意防呆塑料是否有断裂
D. 笔记本键盘进液没关系。
【多选题】
显示器/LCD检验规范正确的是___
A. 观察信号线有无折断、信号线接口内有无断针或歪曲。
B. 闻故障显示器内有无焦臭等异味并对异常现象作详细记录
C. 观察LCD表面有无划伤有无漏液迹象。
D. LCD有1个亮点可以给予更换。
【多选题】
液晶屏操作注意事项正确的是___
A. 液晶屏操作需要液晶保护套或袋保护避免液晶屏划伤和弄脏;
B. 液晶屏只要扣到桌面上就行;
C. 不用金属等硬物挤压或撬液晶边框;
D. 液晶屏不得叠放、液晶屏上不允许放置其他物品。
【多选题】
维修完毕规范操作标准正确的是___
A. 用户的报修故障是否解决
B. 根据验机标准维修完毕后用金钥匙为用户验机
C. 对用户的故障给与合理的解释;
D. 对用户讲述维护使用小常识为用户介绍网上预约服务。
【多选题】
万用表基本功能有哪些___
A. 直流电压
B. 交流电压
C. 直流电流
D. 交流电流
E. 电阻
F. 通断
【多选题】
以下哪些是我们的常用维修工具___
A. 防静电手环
B. 尖嘴钳
C. 老虎钳
D. 镊子
【多选题】
维修工具中用于清洁的工具有___
A. 小刷子
B. 清洁剂
C. 硅脂
D. 吹气囊
【多选题】
PATA接口硬盘的供电电压是多少?___
A. 5V
B. 3.3V
C. 12V
D. -5V
【多选题】
维修过程中应必须遵守的原则是___
A. 从简单的事情做起
B. 先换件测试
C. 先想后做
D. 先软后硬
【多选题】
下列哪些是简单的事情___
A. 观察
B. 换件
C. 环境
D. 测试
【多选题】
针对“电脑在使用过程中经常死机”的问题应主要观察___
A. 市电电压
B. 散热情况
C. 倾听
D. 询问
推荐试题
【单选题】
An administrator wants to restore the vCenter Server Appliance 6.5 from backup. Where can this be accomplished?___
A. from the ESXi Host Client
B. from the VMware vSphere Appliance Management Interface
C. from within the VMware vSphere Web Client
D. from the vCenter Server Appliance Installer
【单选题】
The administrator wants to power on VM-K2, which has a 2GHz CPU reservation. VM-M1, VM-M2, and VM-K1 are all powered on. VM-K2 is not powered on. The exhibit shows the parent and child resource reservations. If Resource Pool RP-KID is configured with an expandable reservation, which statement is true?___
A. VM-K2 will be unable to power on because there are insufficient resources.
B. VM-K2 will be able to power on since resource pool RP-KID has 2GHz available.
C. VM-K2 will be unable to power on because only 2GHz are reserved for RP-KID.
D. VM-K2 will receive resource priority and will be able to power on this scenario.
【单选题】
Which is the block size on the VMFS6 datastore?___
A. All small and large file blocks are 8MB.
B. All small and large file blocks are 1MB.
C. Small file blocks are 512KB. large file blocks are 64MB.
D. Small file blocks are 1MB, large file blocks are 512MB.
【单选题】
When installing vCenter Converter Standalone, why must an administrator perform a client-server installation instead of a local installation?___
A. to manage conversion tasks remotely
B. to convert virtual machines as well as physical machines
C. to allow installation of the Converter agent on remote source machines
D. to hot clone physical or virtual machines
【单选题】
Which is required by vCenter Converter Standalone to convert a physical Red Hat Enterprise Linux 7 machine to a virtual machine?___
A. The Linux machine must be powered off.
B. The Linux machine must have the SSH daemon started.
C. The Linux machine must use a static IP address.
D. The Linux machine must have a fully-qualified domain name.
【单选题】
An administrator is troubleshooting network communications between a vCenter Server and an ESXi 6.5 host. Which log shows the related events between these components?___
A. /var/log/fdm.log
B. /var/log/vpxa.log
C. /var/log/hostd.log
D. /var/log/auth.log
【单选题】
An administrator has recently upgraded from vSphere 6.0 to 6.5, and can no longer see the software iSCSI named vmhba33. Which could be the reason for this?___
A. The upgrade has changed the vmhba name.
B. vSphere 6.5 automates iSCSI configurations.
C. vSphere 6.5 no longer supports software iSCSI.
D. The upgrade has deleted the vmhba.
【单选题】
An administrator is trying to vMotion a VM from his datacenter to a recovery site. Which is the maximum allowed RTT (Round-Trip Time) latency between source and destination host?___
A. 100 milliseconds
B. 150 milliseconds
C. 15 milliseconds
D. 10 milliseconds
【单选题】
Which is required for configuring iSCSI Software Adapter network port binding?___
A. VMkernel of the iSCSI traffic must be load balanced using Route based on IP Hash algorithm.
B. VMkernel of the iSCSI traffic must be load balanced using Route based on Source Virtual Port ID algorithm.
C. VMkernel of the iSCSI traffic must be load balanced using Route based on Source MAC Hash algorithm.
D. VMkernel of the iSCSI traffic must be bound to only one active network adapter.
【单选题】
In vSphere Data Protection 6.1, which is the function of a Backup Verification job?___
A. None. Backup Verification job is not a feature of vSphere Data Protection
B. It is a manual task -Power it on -Verify the guest OS -Check started applications
C. It is an automatic process -Restore a virtual machine -Power it on -Verify that the guest OS is booted by communicating with the Backup Verification agent
D. It is an automatic process -Restore a virtual machine -Power it on -Verify that the guest OC is booted by detecting the VMware ToolsTM "heartbeats"
【单选题】
An administrator has enabled vSphere Distributed Switch Health Check. The hosts connected to that Distributed Switch all display an alert:< vSphere Distributed Switch MTU supported status > .The administrator has all of the VMkernel ports MTU sizes set to 1600. Which action will remedy this problem?___
A. Configure the Distributed Switch to MTU 9100.
B. Disconnect and reconnect the physical network cable.
C. Configure the physical switch to MTU 1600.
D. Disable the Distributed Switch MTU.
【单选题】
Which Host Profile Subprofile configuration is used to configure firewall settings for ESXi hosts?___
A. Advanced Configuration Settings
B. General System Settings
C. Security
D. Networking
【单选题】
Where would a vSphere administrator find general vCenter Server logs on a vCenter Server Appliance?___
A. /var/log/vmware/vpxd/
B. /var/log/messages
C. /etc/vmware-vpx/
D. /var/log/vmware/vsan-health/
【单选题】
An administrator wishes to enable network port mirroring based on source port. Which feature should be enabled?___
A. vSphere standard switch port
B. ERSPAN
C. NSX Virtual Wire
D. VLAN
【单选题】
Which CLI command shows the physical uplink status for a vmnic?___
A. esxcli network ip connection list
B. esxcli network ip neighbor list
C. esxcli network nic get
D. esxcli network nic list
【单选题】
Which is the maximum number of block devices (LUNs) that are supported by ESXi hosts that are running version 6.5?___
A. 1024
B. 512
C. 2048
D. 256
【单选题】
When performing a vCenter Server 5.5 for Windows with Microsoft SQL Server Express database migration to vCenter Server Appliance 6.5, which will be the target database?___
A. Microsoft SQL Server Express 2012R2
B. Microsoft SQL Server Standard 2012R2
C. PostgreSQL
D. Oracle DB 11g
【单选题】
An administrator has multiple vCenter Server 6.5 systems but cannot enable Storage I/O Control (SIOC) on a datastore shared by ESXi hosts managed by the vCenter Server systems. Which action should the administrator take to resolve the issue?___
A. Unmount the datastore and then enable SIOC on the vCenter Server system.
B. Configure the datastore to be managed by a single vCenter Server system.
C. Configure Storage DRS and then enable SIOC on the vCenter Server system.
D. Enable Raw Device Mapping (RDM) on the
E. SXi hosts.
【单选题】
“OneAppServer” is a VM template stored in a content library named “LibraryOne”, but the vSphere administrator is not able to use this template for deployment. Why is the administrator unable to deploy OneAppServer?___
A. OneAppServer must be updated before it can be deployed.
B. LibraryOne is a subscribed library and OneAppServer is not downloaded yet.
C. LibraryOne is published and optimized for syncing over HTTP.
D. OneAppServer was imported from a local file on the system.
【单选题】
An administrator sets the Failover Capacity for both CPU and Memory at 25%. Based on the Exhibit below, how much of the cluster’s total CPU resources are still available to power on additional virtual machines?___
A. 45%
B. 25%
C. 70%
D. 60%
【单选题】
Which statement applies to the vSphere Replication appliance?___
A. Only one vSphere Replication appliance can be deployed per vCenter Server instance.
B. VMware Tools in the vSphere Replication appliance can be upgraded.
C. A single vSphere Replication appliance can manage a maximum of 4000 replications.
D. vSphere Replication is available only with the vSphere
E. ssentials Plus license.
【单选题】
Which esxcli namespace can a vSphere Administrator use to adjust the queue depth?___
A. esxcli system module parameters
B. esxcli storage core device
C. esxcli system module set
D. esxcli storage core adapter
【单选题】
Which statement regarding datastore clusters meets VMware’s recommended best practices?___
A. Clusters should contain only datastores presented from the same storage array.
B. Clusters should contain only datastores with equal hardware acceleration capability.
C. Clusters should contain only datastores with the same capacity.
D. Clusters should contain only datastores using the same connection method (iSCSI, FC, etc.).
【单选题】
What VM Monitoring setting would ensure that the maximum reset window for a virtual machine is 24 hours?___
A. Medium
B. Low
C. High
D. Normal
【单选题】
What is the default space threshold for vSphere Storage DRS?___
A. 80%
B. 70%
C. 90%
D. 95%
【单选题】
Which is the correct sequence to upgrade a vSphere infrastructure?___
A. vCenter Server>ESXi host> VMware Tools>VM compatibility
B. ESXi host>vCenter Server> VMware Tools>VM compatibility
C. vCenter host> ESXi host> VM compatibility> VMware Tools
D. ESXi host>vCenter Server> VM compatibility>VMware Tools
【单选题】
An administrator has a large boot from SAN cluster and wants to ensure consistent configuration by using host profiles. What special considerations are required for boot from SAN hosts?___
A. Change the “Device is shared clusterwide” setting to “false” in the host profile.
B. Verify that the boot LUN is correctly identified as the boot device in the host profile.
C. The boot from SAN device must report as a local device.
D. Host profiles are incompatible with boot from SAN hosts.
【单选题】
When using VMware Converter to import a Windows server and improve the consistency of the destination virtual machine, which optional step can be performed immediately prior to powering down the source server?___
A. Perform a final synchronization task.
B. Remove the server from the network.
C. Uninstall production applications.
D. Remove the server from the Active Directory domain.
【单选题】
Restoration of the vCenter Server Appliance is accomplished using which interface?___
A. vSphere Web Client
B. vSphere Client
C. vCenter Server Appliance Management Interface
D. vCenter Server Appliance GUI Installer
【单选题】
When attempting to migrate a virtual machine to another host in the same cluster, the error message, “Select a valid compute resource” returns. What could cause this error?___
A. Both hosts run different versions of ESXi.
B. Both hosts are not sharing the same datastore.
C. VMware Tools is not installed.
D. Virtual machine has an ISO attached.
【单选题】
When will vSphere Data Protection delete the expired backup image of a Platform Service Controller?___
A. Immediately after the retention period has expired.
B. After the expired backup image is restored.
C. During the next backup window following expiry.
D. During the next maintenance window following expiry.
【单选题】
Group A has permission to download files in Content Library. Group B does not have permission to download files in Content Library. If a user is a member of both groups, what will be the result?___
A. The user cannot download file from Content Library.
B. The user can download file from Content Library.
C. The user cannot access Content Library.
D. The user can access Content Library.
【单选题】
An administrator is trying to set up Host Partial Failure Response, but the Automated option is grayed out. What can the administrator change to enable the Automated option?___
A. Change the vSphere DRS Automation level to Partially Automated.
B. Change the vSphere DRS Automation level to Fully Automated.
C. Enable vSphere HA Host Monitoring.
D. Change the vSphere DPM Automation level to Automatic.
【单选题】
When you attempt to open a virtual machine console from the vSphere Web Client, the console does not connect. The following error message appears:<HTTP ERROR 404> <Problem accessin/.Reason: Not Found>. Why did not connect?___
A. Port 443 is in use.
B. Port 9443 is in use.
C. Port 8443 is in use.
D. Port 22443 is in use.
【单选题】
What new feature was introduced to the Content Library in vSphere 6.5?___
A. Mount an ISO directly from the Content Library.
B. Deploy a virtual machine from an OVF Package in a Content Library.
C. Upload a File from a URL to a Library Item.
D. Upload a File from a Local System to a Library Item.
【单选题】
How can an administrator exclude Encryption rights from a support engineer?___
A. Clone the role Virtual machine power user, remove Cryptographic operations privileges.
B. Clone the role Administrator and assign to the support engineer.
C. Clone the role Virtual machine power user and assign to the support engineer.
D. Clone the role No cryptography administrator and select privileges only for the support engineer.
【单选题】
The administrator must back up a vCenter HA deployment. Which component must be backed up?___
A. Passive node
B. Witness node
C. External database
D. Active node
【单选题】
What is the supported protocol to perform remote L3 traffic monitoring in vSphere 6.5?___
A. VXLAN
B. ERSPAN
C. RSPAN
D. SPAN
【单选题】
What are the minimum hardware requirements for a Windows vCenter Server with embedded PSC that manages a “Small” environment?___
A. 2vCPUs, 16 GB RAM
B. 4 vCPUs, 16 GB RAM
C. 2 vCPUs, 10 GB RAM
D. 4 vCPUs, 10 GB RAM
【单选题】
Which port is used for communication between ESXi and vSphere Data protection?___
A. 80
B. 443
C. 902
D. 22