【单选题】
关于屋面卷材防水施工要求的说法，不正确的有___。
A. 先施工细部，再施工大面
B. 平行屋脊搭接缝应顺流方向
C. 大坡面铺贴应采用满粘法
D. 上下两层卷材垂直铺贴
查看试卷，进入试卷练习
微信扫一扫，开始刷题
答案
D
解析
暂无解析
相关试题
【单选题】
下列现浇混凝土板工程量计算规则中，正确的说法是___。
A. 天沟、挑檐按设计图示尺寸以面积计算
B. 雨篷、阳台板按设计图示尺寸以墙外部分体积计算
C. 现浇挑檐、天沟板与板连接时，以板的外边线为界
D. 伸出墙外的牛腿和雨篷反挑檐不计算
【多选题】
关于隧道工程喷射混凝土施工，说法正确的有___。
A. 喷射作业混凝土利用率高
B. 喷射作业区段宽度一般以1.5-2.Omm为宜
C. 喷射顺序应先墙后拱
D. 喷射作业风压应随风管长度增加而增加
E. 为了确保喷射效果风压通常应大于水压
【多选题】
冷弯性能是指钢材在常温下承受弯曲变形的能力，钢材的冷弯性能指标是通过___进行区分。
A. 试件的伸长率
B. 试件被弯曲的角度
C. 试件弯心直径对试件厚度的比值
D. 试件厚度对试件弯心直径的比值
E. 试件在规定周期内不因弯曲发生断裂所能承受的最大应力
【多选题】
下列说法中___是实现混凝土自防水的技术途径。
A. 适当提高水泥用量、砂率和灰砂比
B. 掺入缓凝剂
C. 使用膨胀水泥或掺用膨胀剂
D. 加入引气减水剂
E. 施工中尽量多留施工缝
【多选题】
下列部位可以设置脚手眼的有___。
A. 120mm厚墙、清水墙、料石墙、独立柱和附墙柱
B. 门窗洞口两侧砖砌体大于200mm范围
C. 宽度为1.2m的窗间墙
D. 过梁上与过梁成60°角的三角形范围及过梁净跨度1/2的高度范围内
E. 梁或梁垫下及其左右大于500mm范围
【多选题】
下列关于施T.现场钢筋进场验收的说法，正确的有___
A. 钢筋进场时，应按规定抽取试件做力学性能和重量偏差检验
B. 钢筋平直无损伤，表面可以有少量油污
C. 钢筋的抗拉强度实测值与屈服强度实测值的比值应大于1.25
D. 当发现钢筋脆断时，应停止使用该批钢筋
E. 钢筋的最大力下总伸长率不应小于9 %
【多选题】
根据《房屋建筑与装饰工程工程量计算规范》GB 50854—2013，混凝土及钢筋混凝土平工程的工程量计算规则，正确的是___。
A. 预制混凝土平板以体积计算，不扣除单个0.3m2 以内的孔洞所占体积
B. 预制混凝土楼梯计算吋，扣除空心踏步板空洞体积
C. 现浇混凝土天沟按设计图示尺寸以长度计算
D. 现浇混凝土散水以面积计算，不扣除单个0.3m2 以内的孔洞所占面积
E. 现浇混凝土压顶、台阶按延长米计算
【多选题】
关于隧道工程喷射混凝土施工，说法正确的有___。
A. 喷头与喷射作业面的最佳距离为1m
B. 喷射作业区段宽度一般以1.5～2.0mm为宜
C. 喷射顺序应先墙后拱
D. 喷射作业风压应随风管长度增加而增加
E. 为了确保喷射效果风压通常应大于水压
【多选题】
关于混凝土冬季施工以下说法正确的有___。
A. 暖棚法一般只用于建筑物面积不大而混凝土工程又很集中的工程
B. 电热法中以电极法较为常用
C. 掺外加剂法施工工艺大大简化，降低冬期施工的工程造价
D. 采用蓄热法时，宜用强度等级高、水化热大的硅酸盐水泥
E. 采用蓄热法时，宜用强度等级低、水化热小的水泥
【多选题】
下盘沿断层面相对下降，这类断层大多是___。
A. 受到水平方向强烈张应力形成的
B. 受到水平方向强烈挤压力形成的
C. 断层线与褶皱轴方向基本一致
D. 断层线与拉应力作用方向基本垂直
E. 断层线与压应力作用方向基本平行
【多选题】
关于路面基层说法正确的是___。
A. 水泥稳定细粒土不能用作二级以上公路高级路面的基层
B. 基层可分为无机结合料稳定类和粒料类
C. 石灰稳定土基层不应作高级路面的基层
D. 级配砾石不可用于二级和二级以下公路的基层
E. 填隙碎石基层只能用于二级公路的基层
【多选题】
掺入 高效减水剂的效果是___。
A. 保持坍落度不变可使混凝土 3d 强度值提高 30%
B. 保持坍落度不变可使混凝土 28d 强度值提高 60%
C. 保持坍落度和强度不变可节约水泥用量 15%
D. 提高钢筋混凝土抗钢筋锈蚀能力
E. 提高钢筋混凝土耐久性
【多选题】
提高砼耐久性的重要措施主要包括___。
A. 针对工程环境合理选择水泥品种
B. 添加加气剂或膨胀剂
C. 提高浇筑和养护的施工质量
D. 改善骨料的级配
E. 控制好温度和湿度
【单选题】
关于钢筋的锚固长度，下列说法不正确的是___。
A. 混凝土结构中的纵向受压钢筋，当计算中充分利用其抗压强度时，锚固长度不应小于相应受拉锚周长度的70%
B. 直接承受动力荷载的结构构件，当纵向受力钢筋的实际配筋面积大于其设计计算面积时，锚固长度修正系数取设计计算面积与实际配筋面积的比值
C. 受压钢筋不应采用末端弯钩和一侧贴焊锚筋的锚固措施
D. 施工过程中易受扰动的钢筋，其纵向受拉钢筋的锚固长度修正系数取1.1
【单选题】
受弯构件的挠度验算中，下列不正确的是___。
A. 挠度验算中，可将计算所得挠度值减去预先起拱值
B. 计算悬臂构件的挠度值时，计算跨度按实际是臂长度的2倍取用
C. 挠度验算在短期刚度的基础上，考虑荷载准永久组合的长期作用对挠度增大的影响
D. 挠度验算是以适筋梁第Ⅲ阶段的应力应变状态为依据
【单选题】
关于混凝土弯剪扭构件的配筋，下列不正确的是___。
A. 沿梁截面周边设置受扭纵筋的间距不应大于250mm
B. 受扭纵筋应按受拉钢筋锚固在支座内
C. 受扭箍筋末端应做成135°弯钩，弯钩端头平直段长度不应小于10d
D. 当采用复合箍筋时，位于截面内部的箍筋不应计入受拥所需箍筋
【单选题】
关于高层建筑的结构平面布置与竖向布置的说法，正确的是___。
A. 当楼层的最大层间位移角不大于规范限值的40%时，楼层竖向构件最大水平位移与楼层平均值的比值可适当放松
B. 级高度高层建筑结构的扭转第一自振周期与平动第一自振周期之比不应大于0.85
C. 剪力墙结构的楼层与其相邻上层的侧向刚度比不宜小于0.9
D. 当上部楼层收进后的水平尺寸大于下部楼层的75%时，为竖向体型收进
【单选题】
砌体在局部受压状态下，其强度的变化是___。
A. 压应力出现高峰现象，强度下降
B. 没有明显变化
C. 有时提高，有时降低，变化无规律
D. 局部受压面积受到周围砌体的约束，横向及纵向变形降低，强度提高
【单选题】
承重用钢材应保证的基本力学性能是___。
A. 抗拉强度.伸长率.冷弯性能和硫.磷含量
B. 抗拉强度.屈服强度.冷弯性能
C. 抗拉强度.伸长率.屈服强度和硫.磷含量
D. 屈服强度.伸长率.冷弯性能
【单选题】
为保证施工安全，一般性硬黏土的临时性挖方边坡值(高：宽)应取为___。
A. 1:1.00~1:125
B. 1:075~1:1.00
C. 1:0.50~1:0.75
D. 1:1.25~1:1.50
【单选题】
厚大基础底板施工容易产生超过规范的温度裂缝，下列关干控制该质量通病的措施不正确的是___。
A. 降低骨料温度
B. 降低水泥用量
C. 采取措施降低混凝土表面温度
D. 采用合理的施工保序
【单选题】
砌体结构施工中在外纵墙与内横墙交界处容易产生留置槎口错误，下列关于该处留槎方式不正确的是___。
A. 无拉筋可以留置斜槎口
B. 有拉筋可以留置斜槎口
C. 无拉筋可以留置直槎口
D. 有拉筋时可留置直槎口
【单选题】
与工程网络计划相比，___是横道图进度计划的缺点。
A. 直观表示计划中工作的持续时间
B. 确定实施计划所需要的资源数量
C. 直观表示计划完成所需要的时间
D. 确定计划中的关键工作和时差优点
【单选题】
流水施工中，下列关于施工段划分的原则说法错误的是___。
A. 施工段数应不小于施工过程数
B. 满足最小工作面的要求
C. 不能设置在原结构伸缩缝处
D. 各施工段劳动力相差不超过15%
【单选题】
下列有关检验批验收程序和组织的说法错误的是___。
A. 检验批是基本验收单元
B. 检验批验收由监理工程师组织
C. 检验批验收数量按有关规范执行
D. 检验批验收中主控项目必须合格
【单选题】
下列有关分部工程质量验收合格规定的说法错误的是___。
A. 所包含的分项工程均应验收合格
B. 施工质量控制资料应完整
C. 观感质量验收应符合要求
D. 主要功能项目的抽查结果应符合要求
【单选题】
用直方图进行工程质量统计分析时，如果质量特性数据分布___，说明质量能力偏大，不经济。
A. 宽度边界达到标准上下界
B. 居中且距上下界有较大距离
C. 一边到达边界一边距边界较远
D. 出现两个数据高峰
推荐试题
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.
【单选题】
An administrator has an application that requires connection directly to PCI devices through a virtual machine. What is a limitation of this configuration? ___
A. Devices must be reserved for PCI passthrough on at least one host on which the virtual machine will run.
B. Snapshots are not supported with DirectPath I/O passthrough devices.
C. A maximum of 18 PCI vSphere
D. irectPath devices can be added to a virtual machine.
【单选题】
The vSphere administrator is configuring directory services for an ESXi host: What should the vSphere administrator do to configure the host to use CAM services? ___
A. Check the Use vSphere Authentication Proxy checkbox.
B. Set Select Directory Service Type to CAM services.
C. Specify CAM$ for the
D. omain.
【单选题】
Which statement is true regarding the licensing of vCenter Server? ___
A. The license for vCenter Server must be provided at the time of installation.
B. Changing the license assigned to vCenter Server requires a restart of the vCenter Server service.
C. Virtual machines can still be powered on if the vCenter Server license expires.
D. Licensing for a single vCenter Server installation is determined by the number of managed virtual machines.
【单选题】
When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected? ___
A. 1 min
B. 5 min
C. 10 min
D. 15min
【单选题】
A developer needs to create a multi-tier development stack for a home lab. Which vSphere product will support the architecture required for the least software cost? ___
A. vSphere Hypervisor
B. vSphere Essentials
C. VMware Player
D. VMware Workstation
【单选题】
An administrator is installing Windows into a virtual machine. The DVD has been mounted on the Host and configured for the virtual machine as shown in the Exhibit. Based on the exhibit, when the virtual machine is booted, why would it attempt to search for a PXE server? ___
A. The CD/DVD device is not connected.
B. The ISO is in the incorrect storage location.
C. The OS minimum requirements have not been met.
D. The CD/DVD device is not set to Client Device.
【单选题】
What component must be installed prior to deploying a vCenter Server in vSphere 6.x? ___
A. vCenter Identity Services
B. Platform Services Controller
C. vCenter Single Sign-On
D. Client Integration Plug-In
【单选题】
What is a valid plug-in status for a plug-in that has been added to a vSphere client? ___
A. Disabled
B. Unknown
C. Stopped
D. Installed
【单选题】
Users of an application are reporting performance issues. The following performance values are observed in the vSphere Web Client: <Host CPU utilization is 90%> <Virtual Machine memory utilization is consistently greater than 90% CPU Ready values are higher than 20%> What could be the cause of the application performance issue? ___
A. The host is lacking the CPU resources required to meet the demand.
B. The host is lacking the memory resources required to meet the demand.
C. The virtual machine is lacking the CPU resources required to meet the demand.
D. The virtual machine is lacking the memory resources required to meet the demand.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is re-provisioning an ESXi host and moving it to another datacenter. Which DCUI option should the administrator use to revert the system configuration to the default settings? ___
A. Reset System Configuration
B. Rebuild Default System Configuration
C. Revert System Configuration
D. Renew Default System Configuration
【单选题】
An administrator has just completed installing an ESXi 6.x host, but doesn't know what address has been configured. Where is the ESXi host IP address configured? ___
A. RVC console
B. Direct Console User Interface
C. vSphere Web Client
D. vSphere Client
【单选题】
When is it possible to place a VMFS5 datastore in maintenance mode? ___
A. When it is a member of a Storage DRS cluster
B. When it is a member of Virtual SAN cluster
C. When it is a member of a multi-extent datastore
D. When it is a member of a Virtual Volume
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Which Single Sign-On deployment mode should an administrator use for two 6.x vCenter Servers configured with linked mode? ___
A. Basic Single Sign-On with vCenter Server Heartbeat
B. Multisite Single Sign-On
C. Basic Single Sign-On
D. Single Sign-On with Linked Mode
【单选题】
What is required when changing a virtual machine name using the vSphere Web Client? ___
A. Verify connectivity to the ESXi host where the virtual machine is running and its inventory list is accessible.
B. Verify in which datastore the virtual machine resides and that you have access and its inventory list is accessible.
C. Verify that virtual machine files are stored in the same datastore and can be accessed in the datastore browser list.
D. Verify the virtual machine is not running in Fault Tolerant mode and that it is not in a Distributed Resource Scheduler cluster.
【单选题】
An administrator deploys vRealize Operations into a vSphere 6.x environment. After the deployment, the administrator notices that badges are not appearing. What is a likely cause of this behavior? ___
A. Badges do not appear until you register vRealize Operations with vCenter Server.
B. Badges do not appear until you register a vCenter Server in vRealize Operations.
C. The vRealize Operations appliance needs to be redeployed.
D. The vCenter Server appliance needs to be redeployed.
【单选题】
How are ports scaled on vSphere Standard Switches (vSS)? ___
A. Ports on a vSS can be dynamically scaled up and down.
B. Ports on a vSS can only be statically scaled up or down.
C. Ports on a vSS can only be dynamically scaled down.
D. Ports on a vSS can only be dynamically scaled up.
【单选题】
A High Availability (HA) cluster is configured to respond to a given number of host failures. The cluster contains virtual machines configured with these settings: VM1 has a 1GHz CPU reservation and no Memory reservation VM2 has a 2GHz CPU reservation and no Memory reservation VM3 has no CPU reservation and no Memory reservation . Given this information, what is the correct slot size for the cluster? ___
A. The CPU Reservation should be set to 32MHz and the memory reservation should be set to 32MB plus memory overhead.
B. The CPU reservation should be set to 1 GHz and the memory reservation should be set to 0MB plus memory overhead.
C. The CPU reservation should be set to 2 GHz, and the memory reservation should be set to 0MB plus the virtual machine memory overhead.
D. The CPU reservation should be set to 2 GHz, and the memory reservation should be set to 32MB, plus the virtual machine memory overhead.
【单选题】
An administrator is planning a vSphere infrastructure with the following specific networking requirements: <The ability to shape inbound (RX) traffic> <Support for Private VLANs (PVLANs)> <Support for LLDP (Link Layer Discovery Protocol)>. What is the minimum vSphere Edition that will support these requirements? ___
A. vSphere Essentials Plus
B. vSphere Standard
C. vSphere Enterprise
D. vSphere
E. nterprise Plus
【单选题】
When you add an ESXi 6.x host to a new Cluster, which vSphere object owns the CPU and Memory resources of the hosts? ___
A. vCenter Server
B. Datacenter
C. Cluster
D. Host
【单选题】
A user is trying to retrieve objects from a SharePoint server and finds the request is taking an excessive amount of time. An administrator tries to isolate the issue and notes the following: Application performance is poor when compared to virtual machines on other hosts. Performance improves when the virtual machine is moved to another host. The virtual machine encounters higher than expected CPU %Ready times. What conclusion can be reached regarding the performance issues for this virtual machine? ___
A. Host Power Management is directly impacting virtual machine performance.
B. The virtual machine has a large number of snapshots.
C. The Path Selection Policy for the storage device is set differently on the affected host.
D. Network I/O control is configured for the portgroup.
【单选题】
A virtual machine template is accidently removed from the vCenter Server Inventory. Which method would be used to recover the template back into the environment?___
A. Use the datastore browser to locate the template, then right click and add the .vmtx file to inventory.
B. Use the datastore browser to locate the template, then right click and add the .vmx file to inventory.
C. Using the Managed Object Browser and adding the template from the ManagedObjectReference:GuestFileManager object.
D. Using the Managed Object Browser and adding the template from the ManagedObjectReference:VirtualDiskManager object.
【单选题】
A vSphere administrator needs to backup a virtual machine that has a Microsoft SQL Server Database installed. Which solution allows for an application quiesce to occur during backup?___
A. VMware vCenter Converter
B. VMware vCenter Site Recovery Manager
C. VMware vSphere Replication
D. VMware vSphere Data Protection Advanced
【单选题】
An administrator is migrating a virtual machine from a Test cluster to a Production cluster. The two environments do not have any shared storage. What is the easiest way to accomplish this task? ___
A. Perform a Storage vMotion.
B. Perform a regular vMotion.
C. Perform a Virtual to Virtual migration.
D. Perform a backup and restore using VMware Data Protection.
