【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
2.刀开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
3.行程开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
4.交流接触器的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
A. 频繁地
B. 偶尔
C. 手动
D. 不需
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16.短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
17.一般电气控制系统中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
18.交流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
19.直流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
20.接触器的额定电压应不小于主电路的___。
A. 短路电压
B. 工作电压
C. 最大电压
D. 峰值电压
【单选题】
21.接触器的额定电流应不小于被控电路的___。
A. 额定电流
B. 负载电流
C. 最大电流
D. 峰值电流
【单选题】
22.对于___工作制的异步电动机,热继电器不能实现可靠的过载保护。
A. 轻载
B. 半载
C. 重复短时
D. 连续
【单选题】
23.对于△接法的异步电动机应选用___结构的热继电器。
A. 四相
B. 三相
C. 两项
D. 单相
【单选题】
24.对于工作环境恶劣、启动频繁的异步电动机,所用热继电器热元件的额定电流可选为电动机额定电流的___倍。
A. 0.95~1.05
B. O.85~0.95
C. 1.05~1.15
D. 1.15~1.50
【单选题】
25.中间继电器的选用依据是控制电路的___、电流类型、所需触点的数量和容量等。
A. 短路电流
B. 电压等级
C. 阻抗大小
D. 绝缘等级
【单选题】
26中间继电器一般用于___中。
A. 网络电路
B. 无线电路
C. 主电路
D. 控制电路
【单选题】
27.行程开关根据安装环境选择防护方式,如开启式或___。
A. 防火式
B. 塑壳式
C. 防护式
D. 铁壳式
【单选题】
28.根据机械与行程开关传力和位移关系选择合适的___。
A. 电流类型
B. 电压等级
C. 接线型式
D. 头部型式
推荐试题
【单选题】
板桩式地锚,打入地中的方向,可分为垂直锚和斜向锚两种,其受力方向最好与锚桩【】,而且拉力的作用点最好靠近地面,这样受力较好。___
A. 互成45°
B. 互成60°
C. 平行
D. 垂直
【单选题】
在瓷绝缘子布线中,转角绝缘子导线应绑扎在【】。___
A. 受力侧
B. 不受力侧
C. 内侧
D. 取得与直线保持一致
【单选题】
容量小于【】的交流接触器,一般采用的灭弧方法是双断口触头和电动力灭弧。___
A. 10A
B. 15A
C. 20A
D. 30A
【单选题】
钳工操作锯割时,一般情况往复速度以每分钟【】为宜,锯软材料时可快些,锯硬材料时可慢些。___
A. 10~30次
B. 20~40次
C. 30~50次
D. 40~60次
【单选题】
电阻和电感串联的单相交流电路中,用【】表示电阻、电感及阻抗之间的关系。___
A. 电压三角形
B. 功率三角形
C. 阻抗三角形
D. 电流三角形
【单选题】
电阻和电感串联的单相交流电路中的无功功率计算公式是【】。___
A. P=UI
B. P=UIcosφ
C. Q=UIsinφ
D. P=Ssinφ
【单选题】
钢芯铝绞线铝股损伤截面超过铝股总面积的【】,应切断重接。___
A. 7﹪
B. 10﹪
C. 17﹪
D. 25﹪
【单选题】
以铜带作为屏蔽层的铜芯挤包绝缘电缆,当电缆线芯截面积在35mm2及以下时,接地线截面不小于【】mm2。___
A. 10
B. 16
C. 25
D. 35
【单选题】
电缆沟(隧道)内的支架间隔【】。___
A. 1m
B. 2m
C. 3m
D. 4m
【单选题】
一般电缆线路每【】个月至少巡视一次。___
A. 1
B. 3
C. 6
D. 12
【单选题】
杆坑需用马道时,一般要求马道的坡度不大于【】。___
A. 30
B. 35
C. 40
D. 45
【单选题】
电压互感器可把高电压变为标准的计量用【】电压,便于计量表和指示仪表接入电路进行测量。___
A. 110V
B. 100V
C. 220V
D. 200V
【单选题】
变压器容量在【】及以上的大工业用户实行两部制电价。___
A. 2000kVA
B. 315kVA
C. 100kVA
D. 50kVA
【单选题】
人体接触漏电设备金属外壳时,所承受的电压是【】。___
A. 跨步电压
B. 外壳对地电压
C. 接触电压
D. 外壳对中性点电压
【单选题】
照明用低压断路器的选择中,长延时整定值【】线路计算负载电流。___
A. 大于
B. 不大于
C. 等于
D. 大于等于
【单选题】
电源频率增加一倍,变压器绕组感应电动势也【】。___
A. 增加一倍
B. 不变
C. 减小一半
D. 略有增加
【单选题】
变压器一次电流随二次电流的增加而【】。___
A. 减小
B. 增加
C. 不变
D. 不能确定
【单选题】
使用钢丝绳的滑车,滑轮槽底的直径D应大于钢丝绳的直径d的【】倍。___
A. 6~7
B. 7~8
C. 8~9
D. 10~11
【单选题】
电能表箱内熔断器的熔断电流最大应为电能表额定电流的【】倍。___
A. 0.9~1.0
B. 1.0~1.2
C. 1.2~1.4
D. 1.4~2.0
【单选题】
在工作人员上下的铁架、梯子上,应悬挂【】标示牌。___
A. 止步!高压危险
B. 禁止攀登,高压危险
C. 在此工作
D. 从此上下
【单选题】
私自超过合同约定的容量用电的,除应拆除私增容设备外,属于两部制电价用户,应补交私增设备容量使用月数的基本电费,并承担【】倍私增容量基本电费的违约使用电费。___
A. 2
B. 3
C. 4
D. 5
【单选题】
在电动机的规格代号中,S表示【】机座。___
A. 长
B. 中
C. 短
D. 加长
【单选题】
QS这个文字符号表示的电气设备为【】。___
A. 断路器
B. 保护开关
C. 隔离开关
D. 低压闸刀开关
【单选题】
有熔断指示器的熔断器,其指示器应装在【】。___
A. 内侧
B. 外侧
C. 便于观察一侧
D. 上侧
【单选题】
拉线安装后对地平面夹角与设计值允许误差:当为10kV及以下架空电力线路时不应大于【】度。___
A. 3
B. 5
C. 7
D. 9
【单选题】
用三只单相电能表测三相四线电路有功电能时,其电能应等于三只表的【】。___
A. 几何和
B. 代数和
C. 分数值
D. 平均值
【单选题】
刀开关起【】的作用,有明显绝缘断开点,以保证检修人员安全。___
A. 切断过负荷电流
B. 切断短路电流
C. 隔离故障
D. 隔离电压
【单选题】
照明线截面选择,应满足【】和机械强度的要求。___
A. 允许载流量
B. 电压降低
C. 平均电流
D. 经济电流
【单选题】
拉线加装警示套管时应涂有明显【】油漆的标志。___
A. 红
B. 黑
C. 白
D. 红、白相间
【单选题】
绝缘导线的绝缘层损伤深度在绝缘层厚度的【】及以上时应进行绝缘修补。___
A. 0.05
B. 0.07
C. 0.1
D. 0.17
【单选题】
电缆出现故障后,受潮部分应予【】。___
A. 烘干
B. 锯除
C. 修复
D. 缠绕防水胶布
【单选题】
终端交流采样不得接入电能计量装置二次回路中,而应优先接入【】柜的电压、电流互感器或计量柜中非电能计量用的电压、电流互感器,所接绕组为测量绕组。___
A. 进线
B. 计量
C. 出线
D. 避雷器
【单选题】
三相三元件用功电能表在测量平衡负载的三相四线电能时,若有U、W两相电流进出线接反,则电能表将【】。___
A. 停转
B. 慢走2/3
C. 倒走1/3
D. 正常
【单选题】
对受电点内难以按电价类别分别装设用电计量装置而执行定比电量计费的用户,供电企业【】个月至少对其用电比例或定量核定一次,用户不得拒绝。___
A. 6
B. 12
C. 24
D. 36
【单选题】
按最大需量计收基本电费,实际计收需量中,在超过确认数【】以上的,超过部分加倍计收基本电费。___
A. 10%
B. 15%
C. 20%
D. 25%
【单选题】
某单相居民客户反映,其用电高峰时电压为230V,则该客户的电压【】。___
A. 超下限了
B. 超上限了
C. 超过220V标准电压,所以不合格
D. 符合允许电压偏差要求
【单选题】
电容器应在额定电压下运行,其最大电压一般不应超过额定电压值的【】倍。___
A. 1.05
B. 1.15
C. 1.25
D. 1.56
【单选题】
在金属容器、坑井、沟道内或潮湿地方工作的行灯电压不大于【】。___
A. 42V
B. 36V
C. 24V
D. 12V
【单选题】
装设剩余电流动作保护器的低压电网必须是电源中性点直接接地的【】系统。___
A. TT
B. TN-C
C. TN-S
D. TN-C-S
【单选题】
按从上到下从左到右的布局,反映【】的图纸为电路图。___
A. 电气设备和配电方式
B. 电气设备和配电线路
C. 电气设备功能关系和配电方式
D. 电气设备相互关系和配电线路