【单选题】
(B737ng)SPCU作用是___
A. 分配直流电源
B. 控制直流电源
C. A&B对
D. A&B都不对
查看试卷，进入试卷练习
微信扫一扫，开始刷题
答案
C
解析
暂无解析
相关试题
【单选题】
(B737ng)start converter unit (SCU)的作用是___
A. 在APU起动过程中直接控制起动发电机来带动APU起动，和ECU没关系
B. 调节APU起动发电机的输出
C. 在APU起动过程中，受ECU控制来监控起动发电机来带动APU起动
D. B & C对
【单选题】
(B737ng)采用恒速传动装置的发电机若频率负载特性不一致___
A. 不能并联
B. 可以并联但有功负载不相等
C. 可以并联但并联后电压不相等
D. 可以并联但并联后频率不相等
【单选题】
(B737ng)当“BUS XFR”电门放于AUTO位，那些控制有自动转换功能？___
A. GCR，AGCR
B. BTB，DC连接继电器，TRU3
C. APB，EPC
D. RCCB，K1，K2，K3，K5，K8
【单选题】
(B737ng)当给飞机接入外部直流电源时，应：___
A. A. 断开电瓶充电跳开关
B. B. 断开外部直流跳开关
C. C. 断开外部直流跳开关，闭合电瓶充电跳开关
D. D. 断开电瓶充电跳开关，闭合外部直流跳开关
【单选题】
(B737ng)当外电源接头面板上的“未使用”和“连接”灯亮时表示外电源:___
A. 插头接触不良,外电源不能使用
B. 插头接触正常,外电源不能使用
C. 插头接触正常,外电源没有被使用
D. 以上答案都不对
【单选题】
(B737ng)电源面板P5-13的TR灯亮是代表___
A. 地面任一个TRU故障.
B. 空中任所有TRU故障
C. 空中TRU1或空中TRU2和TRU3都故障
D. 以上都有可能
【单选题】
(B737ng)电源系统“TR UNIT”灯亮，可能原因为：___
A. 空中，TRU2故障，其它正常
B. 地面，仅当TRU1，2，3同时都发生了故障
C. 空中，TRU1故障，其它正常
D. 空中，TRU3故障,其它正常
【单选题】
(B737ng)电源系统的“ELEC”灯亮的原因是：___
A. 交流系统发生故障
B. 交流和DC系统同时发生故障
C. BPCU发生故障
D. DC系统或备份电源系统故障
【单选题】
(B737ng)电源系统的“STBY PWR OFF”灯亮，则___
A. AC系统故障
B. 直流系统故障
C. AC和DC同时发生故障
D. AC、DC备分汇流条和BAT BUS 任一无电
【单选题】
(B737ng)电源系统的“TR UNIT”灯亮，可能原因是：___
A. 空中，TRU2故障，其它正常
B. 地面，仅当TRU1，2，3同时都发生了故障
C. 空中，TRU3故障,其它正常
D. 空中，TRU1故障，其它正常
【单选题】
(B737ng)飞机交流电源系统向汇流条提供___
A. 单相115／200伏，400赫兹交流电。
B. 三相220伏或单相115伏、400赫兹交流电。
C. 三相115伏或单相200伏、400赫兹交流电。
D. 三相115伏／200伏或单相115伏、400赫兹交流电。
【单选题】
(B737ng)关于standby power control unit (SPCU)说法正确的是___
A. 737-3/4/5和737NG都有
B. 装在驾驶舱P18板内
C. 包含了737-3/4/5的M400和M238的功能
D. 主要作用是控制静变流机的工作
【单选题】
(B737ng)关于standby power control unit (SPCU)装在___
A. 装在驾驶舱P18板内
B. 装在驾驶舱P6板内
C. 装在前电子舱
D. 装在主电子舱
【单选题】
(B737ng)关于start converter unit (SCU)的作用正确的是___
A. 调节APU起动发电机的输出
B. 在APU起动过程中直接控制起动发电机来带动APU起动，和ECU没关系
C. 在APU起动过程中，受ECU控制来监控起动发电机来带动APU起动
D. A&C对
【单选题】
(B737ng)恒装的脱开与复位情况___
A. 只能人工操纵电门脱开，只能在地面复原
B. 只能自动脱开，只能在地面复原
C. 可自动也可人工脱开，可在地面也可在空中复原
D. 可自动也可人工脱开，只能在地面复原
【单选题】
(B737ng)交流备用汇流条正常供电来自___
A. AC TRANSFER BUS 1
B. AC TRANSFER BUS 2
C. AC MAIN BUS 1
D. AC MAIN BUS 2
【单选题】
(B737ng)哪两个接触器可同时在接通位___
A. A．一号发电机GB和一号APUGB
B. B．二号发电机GB和二号APUGB
C. C．一号外电源接触器和一号APUGB
D. D．一号APUGB和二号APUGB
【单选题】
(B737ng)南航B737飞机有两个主电瓶的机型是___
A. B737-3/4/5
B. B737-700
C. 2005年前交付的B737-800
D. 2005年后交付最新的B737-800飞机
【单选题】
(B737ng)如采1号发电机失效,则: ___
A. 只有1号发电机汇流条供屯的前厨房断电.
B. 只有1号发电机汇流条供屯的后厨房断电.
C. 所有厨房电源都将断掉.
D. 以上说法都不对.
【单选题】
(B737ng)如果飞机左、右IDG和APU的发电机可用；2号交流转换汇流条发生短路，头顶板有那一些电源灯亮___
A. APU GEN OFF BUS和2号GEN OFF BUS
B. 2号SOURCE OFF加上选择A提到的灯
C. 2号TRANSFER BUS OFF加上选择A提到的灯
D. 以上提到的灯都会亮
【单选题】
(B737ng)使用地面电源起动APU后，P5-13板APU GEN OFF灯灭,此时以下接触器（BTC1、BTC2、EPC、APC）的通断位置应该是：___
A. 通；通；通；通
B. 通；通；断；通
C. 通；通；通；断
D. 通；断；通；通
【单选题】
(B737ng)下面哪种情况不能使发动机驱动的发电机控制继电器跳开? ___
A. A． 将相应的发电机电门置于0FF位
B. B． 过压(0V)保护或欠压(LV)保护
C. C． 过频(0F)保护或欠颜(UF)保护
D. D． 过流(<3C)保护
【单选题】
(B737ng)下面说法哪个是错误的？___
A. AGCU和SCU一起控制APB的打开与闭合。
B. APU起动发电机的激励电压来自AGCU的调压电路。
C. APU起动发电机的激励电压来自SCU的调压电路。
D. IDG发电机的激励电压由GCU来调压。
【单选题】
(B737ng)下面说法正确的是：___
A. A． 机长和负驾驶的时钟是一样的，但不能互换，因为机长的时钟还提供时间数据给FMC
B. B． 机长的时钟使用的是28VDC热电瓶汇流条，而负驾驶时钟使用的是28VDC电瓶汇流条
C. C． 当28VDC电瓶汇流条断电时，由于28VDC热电瓶汇流条供电正常，所以时钟仍能计时，并且时钟上仍有指示
D. D． 以上说法都是错误的
【单选题】
(B737ng)用地面电源起动好APU后，P5-13板APU GEN OFF灯灭。此时以下接触器（BTC1、BTC2、EPC、APC）的通断位置应该是：___
A. 通；通；通；通
B. 通；通；通；断
C. 通；通；断；通
D. 通；断；通；通
【单选题】
(B737ng)与一号发电机断路器不能互换的是:___
A. A．二号发电机断路器(GB)
B. B．二号发电机APU发电机断路器
C. C．一号APU发电机断路器
D. D．汇流条转换继电器
【单选题】
(B737ng)在电源转换的迅间，由那一汇流条向 DEU1 & DEU2 供电___
A. AC standby bus
B. DC standby bus
C. Hot BAT bus
D. Main AC bus 1
推荐试题
【多选题】
In order for a company to meet regulatory requirements, all ESXi 6.x Hosts must be configured to direct logs to a syslog server. What are two ways ESXi hosts can configured for this action? (Choose two)___
A. Use the esxcli system syslog command.
B. Edit them in the ESXi host Advanced System Settings.
C. From the Syslog collector user interface of the Web Client.
D. Syslog logging is not available for
E. SXi Hosts.
【多选题】
Which three actions can be executed when an alarm is triggered? (Choose three.)___
A. Send an email.
B. Send an SNMP trap.
C. Run a script or command.
D. Run an Orchestrator workflow.
E. Send a trigger to syslog.
【多选题】
An administrator is attempting to power on a virtual machine, but is unable to do so. Which two reasons are probable causes of the failure? (Choose two.)___
A. Storage access to the virtual machine swap file has been lost.
B. One of the virtual machine VMDK files is locked.
C. Virtual machine is running CentOS 7.0 64-bit.
D. Virtual machine has Hyper-Threading enabled.
【多选题】
An administrator has configured a host profile so that ESXi 6.x hosts will point to the corporate NTP server for time synchronization. The NTP server is located at 10.0.30.213, but time has not been synchronized properly across the ESXi hosts. The administrator reviews Host Profile settings as shown in the Exhibit. Which two steps are required to resolve the issue? (Choose two.)___
A. Correct the NTP server IP address.
B. Check the host for host profile compliance.
C. Remediate the host based on the updated host profile.
D. Change the NTP server to the FQDN as IP Addresses are not supported.
【多选题】
An administrator is attempting to migrate a large Hadoop virtual machine using vMotion. The administrator notices a delay when the machine is quiesced. The Hadoop virtual machine is processing many transactions a second to an in-memory database. Which two actions would help reduce the amount of time needed to perform a vMotion on this virtual machine? (Choose two.)___
A. Use multiple NICs for the vMotion vmkernel port.
B. Use a 10Gbps Network card for the vMotion vmkernel port.
C. Add an additional management network to help transmit the data quicker.
D. Disable Fault Tolerance before performing the vMotion.
【多选题】
An administrator is installing a new network card in an ESXi 6.x host that is part of a vSphere cluster. When the host is placed into maintenance mode, the vSphere Web Client displays the progress bar at 2% for over 30 minutes. Which two are likely reasons for this occurrence? (Choose two.)___
A. Maintenance mode is unable to migrate all virtual machines from the host.
B. There is a large number of virtual machines that must be migrated from the host.
C. VMware High Availability is in the process of reconfiguring the cluster.
D. Each virtual machine on the
E. SXi host must be reconfigured to recognize the new adapter.
【多选题】
Which two events happen when Distributed Resource Scheduler (DRS) is disabled? (Choose two.)___
A. The cluster's resource pool heirarchy and affinity rules are re-established when DRS is turned back on.
B. The cluster's resource pool hierarchy and affinity rules are not re-established when DRS is turned back on.
C. The cluster's resource pools are removed from the cluster.
D. The cluster's resource pools are removed from the cluster and assigned to the hosts.
【多选题】
Which two networking connection types can be configured on a virtual switch? (Choose two.)___
A. Virtual machine portgroups
B. VMkernel services (such as NFS, iSCSI, or vMotion) to the physical network
C. Web services over the Management Network
D. NFS and FCoE storage services
【多选题】
An administrator creates a DRS cluster of eight ESXi 6.x hosts. There are 10 virtual machines balanced across the hosts. An attempt to place the first host into maintenance mode fails. What are two reasons that the host failed to enter maintenance mode? (Choose two.)___
A. The DRS cluster Automation Level is set to Partially Automated mode.
B. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Should run on hosts in group.
C. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Must run on hosts in group.
D. One of the virtual machines on the
E. SXi Host entering maintenance mode is configured with an individual Automation Level set to Partially Automated.
【多选题】
When modifying a vApp, which two vSphere entities can be added? (Choose two.)___
A. A resource pool
B. A network pool
C. A vApp
D. A folder
【多选题】
From which two locations in the inventory hierarchy can you deploy a virtual machine using a template? (Choose two.)___
A. Directly from the template.
B. From a compute resource.
C. From an existing virtual machine.
D. From a Datastore.
【多选题】
A company has decided to implement Virtual SAN within their vSphere 6.x environment. The Virtual SAN cluster will be composed of three ESXi 6.x hosts that are on the Virtual SAN Ready Node list. Each ESXi host includes: <Two SAS Controllers that support Passthrough Mode> < Four Solid State Drives (SSDs) 1TB in size each> <20 SAS Magnetic Disks (MDs) 1TB in size each> <The SSDs and MDs are evenly split between the two SAS controllers>. The company will pilot a Virtual SAN cluster utilizing VMware best practices while maximizing storage capacity. The Virtual SAN cluster will use Manual Mode. Which two Disk Group configurations would meet the stated configuration requirements? (Choose two.)___
A. 4 disk groups with 1 SSD and 5 MDs each
B. 2 disk groups with 1 SSD and 7 MDs each
C. 2 disk groups with 2 SSDs and 7 MDs each
D. 2 disk groups with 1 SSD and 10 MDs each
【多选题】
A physical Windows 2008 R2 Server is converted to a virtual machine using VMware vCenter Converter. Upon completion of the conversion and subsequent power on operation, the virtual machine fails to boot and the message below is observed in the Console of the virtual machine: <STOP 0x0000007B INACCESSIBLE_BOOT_DEVICE>. Which two potential issues may be causing this boot failure? (Choose two.)___
A. An incorrect SCSI controller was selected during conversion.
B. Incompatible software drivers were migrated into the virtual machine from the source machine.
C. The vmdk file backing the virtual machine was thick provisioned.
D. A snapshot was taken immediately after the conversion completed.
【多选题】
An administrator is configuring the Failover Order option on a vSphere Distributed Switch. Which two options should be used with IP-hash load balancing? (Choose two.)___
A. Active Uplinks
B. Standby Uplinks
C. Unused Uplinks
D. Override Failover Order
【多选题】
An administrator is configuring the Maximum Transmission Unit value on a vSphere Distributed Switch. Which two options are typical values for ESXi networking? (Choose two.)___
A. 1492
B. 1500
C. 9000
D. 9089
【多选题】
Which two configurable options apply to both virtual machine CPU and memory allocation? (Choose two.)___
A. Reservation
B. Shares
C. Resource Pool
D. Reserve All
【多选题】
When attempting to power on a Virtual Machine you observe the following error: <Cannot open the disk '/vmfs/volumes/volume/vm/vm-000002.vmdk' or one of the snapshot disks it depends on.> Which three actions will be the best solutions to address this problem? (Choose three.)___
A. Verify that the virtual machine's disk files are present.
B. Investigate the host and virtual machine log files.
C. Verify the vmdk descriptor files and if required, recreate them.
D. Delete the disk file preventing the power on operation.
E. Migrate or register the virtual machine to a different host.
【多选题】
An administrator has been tasked with enabling High Availability ___ on a cluster in a vSphere 6.x environment with default settings. The cluster configures properly and there are no errors. The next day when powering on a virtual machine, an error is presented: <Not Enough Failover Resources>. Which three scenarios are likely causes of this error message? (Choose three.)(CDE)
A. The default VM Monitoring Sensitivity is set too high.
B. There are not enough datastore heartbeat datastores configured by default.
C. The default slot size in the cluster is set too high.
D. There are virtual machines with large CPU reservations.
E. A host is in maintenance mode for a replacement of a failed Hard Drive.
【多选题】
vMotion can be performed between which three physical boundaries? (Choose three.)___
A. Between two vCenter Server Systems
B. Between two vSphere Distributed Virtual Switches
C. Between two vCenter Server Datacenter objects
D. Between two VMware NSX Layer 4 segments
E. Between two NFS datastores
【多选题】
An administrator configures vSphere Replication for a virtual machine and enables multiple point in time (PIT) instances under the recovery settings in the Configure Replication wizard. Which two statements are correct for vSphere Replication with multiple point in time instances enabled? (Choose two.)___
A. vSphere Replication retains a number of snapshot instances of the virtual machine on the target site based on the retention policy that you specify.
B. vSphere Replication uses the virtual machine's snapshot instances to define the target site Point in Time instance based on the retention policy that you specify.
C. vSphere Replication does not support virtual machines with snapshots.
D. vSphere Replication supports virtual machines with snapshots.
【多选题】
An administrator is virtualizing a physical application server and adding it to an existing multi-tiered vApp. The application license is currently tied to the physical NIC's MAC address, so the administrator needs to ensure the license will function properly in the virtual machine. Which two actions can the administrator take to satisfy this task? (Choose two.)___
A. Set the MAC address for the vNIC in the guest operating system.
B. Install the physical server's NIC into the ESXi host.
C. Configure the MAC address for the vNIC using the vSphere Web Client.
D. Assign the physical server NIC's MAC address in the vSphere Distributed Switch.
【多选题】
Which two Fibre Channel zoning options are supported with vSphere 6.x? (Choose two.)___
A. Single-Initiator
B. Single-Initiator-Single-Target
C. Multiple-Initiators-Single-Target
D. Multiple-Initiators-Multiple-Targets
【多选题】
An administrator is attempting to remove an ESXi 6.x host from a vSphere Distributed Switch (vDS). When the administrator attempts to remove the host, the following error is observed: <The resource '16' is still in use.> What three steps are needed to successfully remove the host from the switch? (Choose three.)___
A. Select Manage Ports on the vDS for the host.
B. Locate all ports currently in use on the vDS for the host.
C. Migrate or delete any vmkernel or virtual machine adapters associated with the switch.
D. Remove all network cards from the switch before trying to remove the host.
E. Create a standard switch for everything to be automatically be migrated to.
【多选题】
Which two Virtual SAN related actions might start resynchronization of virtual machine objects? (Choose two.)___
A. Editing a virtual machine storage policy to increase the number of replicas.
B. Editing a virtual machine storage policy to reduce the number of replicas.
C. Editing a virtual machine storage policy to increase the number of disk stripes.
D. Editing a virtual machine storage policy to reduce the number of disk stripes.
【多选题】
An administrator is troubleshooting basic network connectivity issues. Which two scenarios are potential issues that this administrator might face? (Choose two.)___
A. The vSwitch is not attached to the correct physical network.
B. The portgroup is not configured to use correct VLAN.
C. Traffic shaping is configured incorrectly.
D. Jumbo frames is configured incorrectly.
【多选题】
Which three items should be validated prior to installing ESXi 6.x? (Choose three.)___
A. Remote Storage has been disconnected.
B. Installation media is available.
C. Server hardware clock is set to UTC.
D. Storage has been partitioned with a VMFS volume.
E. Network cards have been setup to use Jumbo
F. rames.
【多选题】
An administrator is performing an interactive installation of ESXi 6.x. Which three options are available for installation? (Choose three.)___
A. DVD
B. USB
C. PXE
D. Scripted
E. Auto Deploy
【多选题】
After installation of a host in your test environment, you need to move it to production. The only major change that needs to be made is that the hostname of the server needs to change. What are two ways that an administrator can change the host name without editing configuration files on the host directly? (Choose two.)___
A. Login to the Direct Console User Interface and change it from here.
B. Edit the Default TCP/IP Configuration from the vSphere Web Client.
C. Use the Ruby vSphere Client to send a script to the ESXi host that updates the hostname.
D. Update the information in DNS and the
E. SXi host will automatically update with these changes.
【多选题】
An administrator has unsuccessfully attempted several times to install an Operating System inside a virtual machine. The administrator finds that the installation fails at random intervals. Which two actions can be taken to resolve this issue? (Choose two.)___
A. Verify the md5sum and if invalid, download the installation files again.
B. Attempt the installation an additional time.
C. Attempt to use a different installation media or installation method.
D. Create a new virtual machine and attempt the installation with the existing media.
【多选题】
VMware tools is failing to install on a Microsoft Windows virtual machine. What are two possible situations that would prevent the installation? (Choose two.)___
A. The VMware tools installation media is corrupt.
B. The incorrect Operating System was selected in the virtual machine options.
C. The software prerequisites have not been installed.
D. The prerequisite services have not been started.
【多选题】
As part of a multisite Single Sign-On (SSO) deployment what two steps are required to ensure that a change to one Single Sign-On instance is propagated to the other instances? (Choose two.)___
A. Schedule a Replication Task on the primary instance
B. Select the first instance during the installation of subsequent instances
C. During the installation of each instance choose Linked-Mode
D. Enable Synchronize to Active Directory on each instance
【多选题】
You need to add an object to an existing vApp using the vSphere Web Client. How is this accomplished?___
A. Create an Object Inside the vApp.
B. Add an Object to a vApp.
C. Add an Object to the
D. atastore the vApp is located in.
【多选题】
Which three steps must be taken to use vSphere Update Manager 6.x to upgrade an ESXi 5.5 host to vSphere 6.x? (Choose three.)___
A. Download an ESXi Image.
B. Configure the vSphere Update Manager Download Service.
C. Create a baseline and attach it to the ESXi Host.
D. Scan the vCenter Content Library for the
E. SXi Image.
【多选题】
Which two options would allow a database administrator, with no access to the vSphere infrastructure, to connect to a virtual machine? (Choose two.)___
A. Use the Virtual Machine Remote Console (VMRC).
B. Use Remote Desktop Protocol (RDP) to connect.
C. Ask the vSphere administrator to grant permission to access the console through vCenter Server.
D. Ask the vSphere administrator to grant permission to access with the Horizon View Direct Connect Client.
【多选题】
Which three are architecture components of vRealize Operations? (Choose three.)___
A. Identity Server
B. Administrative Server
C. Analytics Server
D. Database Server
E. Connection Broker
