【单选题】
The opposite meaning of“speedup”is_________
A. slowdown
B. speeddown
C. speedlow
D. slowby
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
Pilot turns on squawk______to request a squawk number. ___
A. 3000
B. 3500
C. 4000
D. 2000
【单选题】
First______assistance means doctor and ambulance in an emergency condition. ___
A. emergency
B. priority
C. aid
D. help
【单选题】
When somebody is reported hurt on board,maybe it will need______assistance on arrival. ___
A. fire-cart
B. medical
C. police
D. wheelchair
【单选题】
In emergency descent procedure,the pilot should turn right______out of the route while descending. ___
A. 40°
B. 30°
C. 20器
D. 15°
【单选题】
管制员在对空指挥过程中,越是繁忙的时候,语速应___
A. 保持平稳,避免频繁重复指令
B. 尽量快些,才能指挥更多飞机
C. 降低语速,避免口误
D. 时快时慢,引起机组的注意
【单选题】
According to ICAO,a standard holding pattern should all turn to the______.___
A. right
B. west
C. left
D. east
【单选题】
The standard altimeter setting is______inhpa. ___
A. 1013.20062
B. 1010.10062
C. 29.92002
D. 30.10002
【单选题】
2500f/m rate of vertical speed is equal to______.___
A. 10m/s
B. 15m/s
C. 20m/s
D. 25m/s
【单选题】
陆空通话时,什么时候推荐使用“IMMEDIATELY(立即)”这个词:___
A. 相对飞行穿高度时
B. 天气差时,担心自己会忘记某个正在改变高度的动态
C. 飞机多时,为了节省精力
D. 在紧急情况下,用于冲突解脱时
【单选题】
Standard rate for a turning is______degrees per second. ___
A. 4
B. 6
C. 3
D. 2
【单选题】
What is the best course of action for a pilot to follow when thunderstorms are observed along the route of flight? ___
A. Fly below the thunderstorms
B. Climb over the thunderstorms
C. Disregard the thunderstorms
D. Take any action to avoid all thunderstorms
【单选题】
The subdivision of frequencies is______MHZ. ___
A. 0.025
B. 0.035
C. 0.02
D. 0.015
【单选题】
Aeronautical chart is divided into two categories,______. ___
A. Aeronautical map and special type of aeronautical chart
B. En-route chart and approach chart
C. Area chart and standard instrument arrival and departure chart
D. Aerodrome chart and area chart
【单选题】
Aircraft are required to comply with ATC instructions within______.___
A. advisory airspace
B. domestic airspace
C. controlled airspace
D. international airspace
【单选题】
Amendments to the initial clearance will be issued at anytime an air traffic controller deems such action necessary to______.___
A. avoid possible confliction between aircraft
B. correct the previously issued clearance
C. cancel the flight plan
D. expedite the traffic
【单选题】
研究表明,当耳机话筒的位置距离嘴( )英寸且稍微偏下时,传输的声音质量最佳。(注:1英寸=2.54CM)___
A. 0.25-0.5
B. 0.75-1
C. 1.25-1.5
D. 1.75-2
【单选题】
“I want to divert to shanghai” is equal to______.___
A. I want to our destination Shanghai
B. I want to overfly Shanghai
C. I want to alternate to land at Shanghai
D. I want to call Shanghai control
【单选题】
When an aircraft is being subjected to unlawful interference, the pilot should try to notify _______ of this fact.___
A. the appropriate ATC units
B. company
C. the passengers on board
D. air attendants
【单选题】
When pilot say“Did you pick it upon your screen?”,that means______.___
A. did you pick up your screen?
B. did you see it on your screen?
C. did your screen pick me up?
D. did you change your radar?
【单选题】
ATC clearance does not contain______.___
A. clearance limit
B. altitude data
C. route of flight
D. flight direction
【单选题】
When pilot sets an altimeter setting to a QNH,that will indicate_________
A. flight level
B. altitude
C. height
D. safety level
【单选题】
When pilots set a pressure of 29.92 in mercury to indicate_________
A. altitude
B. height
C. flight level
D. safety level
【单选题】
管制员还应当对管制指令当中的不同内容进行适当的排序,相对重要的内容应当排列在管制指令的 ( )位置___
A. 前面
B. 中间
C. 尾部
D. 以上都可以
【单选题】
When Beijing time is 0801,Zulu time should be______.___
A. 2001
B. 1
C. 601
D. 1601
【单选题】
Emergency frequency is______.___
A. 121.5MHZ
B. 120.5MHZ
C. 121MHZ
D. 119.0MHZ
【单选题】
“PAN” is the international RTF______signal___
A. emergency
B. distress
C. urgency
D. dangerous
【单选题】
“MAYDAY” is the international RTF______signal.___
A. emergency
B. distress
C. urgency
D. dangerous
【单选题】
According to ICAO definition, a condition concerning the safety of an aircraft or other vehicle or of some person on board or within sight but which does not require immediate assistance is _______ .___
A. urgency
B. dangerous
C. emergency
D. distress
【单选题】
Which SSR Code is not right?___
A. 7020
B. 8025
C. 6060
D. 4021
【单选题】
______is the accepted standard for worldwide time signal broadcast used for aviation.___
A. GMT
B. LT
C. UTC
D. SST
【单选题】
_____means the level is measured in 1013.2 pha___
A. Level
B. Height
C. Altitude
D. Flight level
【单选题】
An aircraft known or believed to be in a state of emergency should be given______over other aircraft.___
A. way
B. flight plan
C. instruction
D. priority
【单选题】
管制话筒正确使用方法是:___
A. PTT发射键还没有完全按下时就开始发指令
B. 指令还没有结束就松开PTT发射键
C. 按PTT发射键与发话同时进行,松开PTT发射键与发话同时进行
D. 先按下话筒PTT发射键,然后再开始对空发话,发话完毕后再松开话筒PTT发射键
【单选题】
SSR code is a______digital number.___
A. two
B. six
C. one
D. four
【单选题】
Traffic information should include_________
A. direction of aircraft concerned
B. weather
C. speed of aircraft
D. heading of aircraft
【单选题】
根据区管中心业务通告,管制员通知机组转换频率的管制指令应当与其他管制指令( )。___
A. 分开发布
B. 同时发布
C. 无特别要求
【单选题】
20NM is equal to.___
A. 40km
B. 38km
C. 37km
D. 41km
【单选题】
The altimeter setting used in en-route flight should be______hpa___
A. 1019
B. 1013
C. 2992
D. 1000
【单选题】
Larger separations than the specified minima should be applied whenever in.___
A. turbulence
B. bad weather
C. a raining day
D. highlevel
【单选题】
_______is air traffic control service for controlled flights in control areas___
A. Route service
B. En-route fly service
C. Area control service
D. Deviation control service
推荐试题
【单选题】
马氏体片的粗细,主要取决于___
A. 淬火冷却速度
B. 母相奥氏体的晶粒度
C. Ms点的高低
D. 淬火加热速度
【单选题】
影响产品制造质量的因素中,除了人、机、方法、材料、和测量外,还有 ___
A. 工具夹具
B. 定位装置
C. 环境
D. 量具
【单选题】
当零件的两个加工表面的尺寸精度与形状精度的要求均很高,同时它们之间的位置精度要求也很高,在设计工艺过程和选择精基准时,遵循的基准选择原则是 ___
A. 基准重合
B. 基准统一
C. 自为基准
D. 互为基准
【单选题】
属于压焊的焊接方法是___
A. 摩擦焊
B. 气焊
C. 电弧焊
D. 埋弧焊
【单选题】
焊接性能最好的材料是 ___
A. 低碳钢
B. 高碳钢
C. 灰铸体
D. 镁合金
【单选题】
某主轴材料为38CrMoAlA,需渗氮处理。在进行该主轴工艺路线设计时,渗氮处理应安排在___
A. 粗加工前
B. 粗加工与半精车之间
C. 粗磨与精磨之间
D. 半精车与粗磨之间
【单选题】
车间原来10小时生产800件,改进工艺后8小时生产800件,改进工艺后生产效率提高了多少___
A. 10%
B. 20%
C. 25%
D. 30%
【单选题】
下列属于定心夹紧机构的是___
A. 螺旋夹紧压板
B. 四爪单动卡盘
C. 偏心夹紧机构
D. 三爪卡盘
【单选题】
轴类零件加工最常用的定位基准是___
A. 中心孔
B. 端面
C. 内孔
D. 外圆
【单选题】
工序图中的粗直线代表___
A. 零件轮廓
B. 加工内容
C. 测量基准
D. 定位基准
【单选题】
最大极限尺寸减其基本尺寸所得代数差称为___
A. 公差
B. 偏差
C. 上偏差
D. 下偏差
【单选题】
焊接时开坡口的目的主要是为了___
A. 增加熔深
B. 保证焊透
C. 增加熔合比
D. 减小热影响区
【单选题】
焊接裂纹在重要的焊接接头中是____存在的一种缺陷___
A. 允许
B. 数量不多时允许
C. 不允许
D. 数量多时允许
【单选题】
电弧焊是利用____作为热源的熔焊方法___
A. 电弧
B. 气体燃烧火焰
C. 化学反应热
D. 电能
【单选题】
下列焊接方法中属于固态焊接的是___
A. 熔化极气体保护焊
B. 埋弧焊
C. 摩擦焊
D. 手工电弧焊
【单选题】
目前CO2气体保护焊主要用于___
A. 低碳钢和低合金钢
B. 低合金钢和高合金钢
C. 不锈钢和高合金钢
D. 不锈钢和耐热钢
【单选题】
磁弧焊接的特性下列哪种不适合___
A. 熔化焊
B. 固态焊
C. 压力焊
D. 需焊接保护气体
【单选题】
温锻生产过程中,加热机出料槽剔出的坯料,采用_____方式冷却___
A. 风冷
B. 水冷
C. 自然冷却
D. 冰块
【单选题】
温锻生产过程中,坯料使用____方式加热到生产温度___
A. 电加热
B. 煤炭
C. 煤气
D. 天然气
【单选题】
SDS抛丸机抛丸坯料用的抛丸砂一般是_____材质___
A. 钢铁
B. 铜
C. 陶瓷
D. 塑料
【单选题】
精锻棒料落料后,下道工序是___
A. 抛丸
B. 上料
C. 加热
D. 温锻
【单选题】
坯料加热过程中,采用_____对加热温度进行监测,确保符合工艺温度要求___
A. 手持式测温仪
B. 高温测温仪
C. 在线测温仪
D. 目测
【单选题】
精锻预热坯料温度是___
A. 100~160℃
B. 200~260℃
C. 300~360℃
D. 400~460℃
【单选题】
精锻锻打前坯料温度是___
A. 850~940℃
B. 950~1040℃
C. 750~840℃
D. 650~760℃
【单选题】
温锻预涂石墨浓度是___
A. 7~9%
B. 4~9%
C. 1~2%
D. 2~9%
【单选题】
温锻润滑剂是___
A. 石墨
B. 水
C. 油
D. 气
【单选题】
SDS温锻压机有_____工位___
A. 5
B. 2
C. 3
D. 4
【单选题】
申江厂温锻压机是___
A. 2000吨
B. 2500吨
C. 3000吨
D. 4000吨
【单选题】
申江厂冷精整压机是___
A. 400吨
B. 500吨
C. 300吨
D. 800吨
【单选题】
精锻完成锻打后,要经过___
A. 可控冷却
B. 油冷
C. 回火
D. 退火
【单选题】
生产过程中,经可控冷却直接进行下道抛丸和冷精整时,要求在抛丸前用手持测温仪测量毛坯表面温度,要求温度<____℃___
A. 120
B. 150
C. 180
D. 200
【单选题】
冷精整生产线若使用已超过设计寿命的模具时,目测频率必须至少提高___
A. 1/4
B. 1/3
【单选题】
使用皂化工艺生产外星轮冷精整精锻件时,每次外星轮冷精整换模时必须在冲头与芯棒间添加____#抗磨液压油___
A. 44
B. 45
C. 46
D. 47
【单选题】
皂化使用皂化机进行,皂化的工艺参数按工艺卡上要求的设备参数执行,皂化温度是___
A. 50~60℃
B. 40~50℃
C. 30~40℃
D. 20~30℃
【单选题】
冷精整首件送三座标精测的工件尺寸公差需收紧____%___
A. 10
B. 15
C. 20
D. 30
【单选题】
温锻件经抛丸后要求工件表面基本呈 ___
A. 灰色
B. 黑色
C. ,金属色
D. 氧化色
【单选题】
皂化冷精整后的工件需要进行____处理___
A. 清洗
B. 抛丸
C. 防锈
D. 沥干
【单选题】
外星轮经可控冷却输送带后,柄部硬度一般为___
A. HB109~120
B. HB200~300
C. HB209~252
D. HB300~400
【单选题】
外星轮经可控冷却输送带后,锻件柄部晶粒度要求为___
A. 5~6级
B. 5~7级
C. , 5~9级
D. 5~10级
【单选题】
操作面板上的“OFFSET”是什么含义___
A. 编辑
B. 刀具偏置补偿
C. 自动加工
D. 手动模式