【单选题】
测量接地电阻时,电位探针应接在距接地端( )m的地方。 ___
A. 5
B. 20
C. 40
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
B
解析
暂无解析
相关试题
【单选题】
事故照明一般采用( )。 ___
A. 日光灯
B. 白炽灯
C. 高压汞灯
【单选题】
通电线圈产生的磁场方向不但与电流方向有关,而且还与线圈( )有关。 ___
A. 长度
B. 绕向
C. 体积
【单选题】
电磁力的大小与导体的有效长度成( )。 ___
A. 正比
B. 反比
C. 不变
【单选题】
组合开关用于电动机可逆控制时,( )允许反向接通。 ___
A. 可在电动机停后就
B. 不必在电动机完全停转后就
C. 必须在电动机完全停转后才
【单选题】
在电力控制系统中,使用最广泛的是( )式交流接触器。 ___
A. 气动
B. 电磁
C. 液动
【单选题】
在对可能存在较高跨步电压的接地故障点进行检查时,室内不得接近故障点( )m以内。 ___
A. 3
B. 2
C. 4
【单选题】
接地电阻测量仪主要由手摇发电机、( )、电位器,以及检流计组成。 ___
A. 电压互感器
B. 电流互感器
C. 变压器
【单选题】
万用表由表头、( )及转换开关三个主要部分组成。 ___
A. 线圈
B. 测量电路
C. 指针
【单选题】
电容器组禁止( )。 ___
A. 带电合闸
B. 带电荷合闸
C. 停电合闸
【单选题】
当一个熔断器保护一只灯时,熔断器应串联在开关( ) ___
A. 前
B. 后
C. 中
【单选题】
线路单相短路是指( )。 ___
A. 电流太大
B. 功率太大
C. 零火线直接接通
【单选题】
螺口灯头的螺纹应与( )相接。 ___
A. 零线
B. 相线
C. 地线
【单选题】
运输液化气,石油等的槽车在行驶时,在槽车底部应采用金属链条或导电橡胶使之与大地接触,其目的是( )。 ___
A. 泄漏槽车行驶中产生的静电荷
B. 中和槽车行驶中产生的静电荷
C. 使槽车与大地等电位
【单选题】
感应电流的方向总是使感应电流的磁场阻碍引起感应电流的磁通的变化,这一定律称为( )。 ___
A. 法拉第定律
B. 特斯拉定律
C. 楞次定律
【单选题】
旋转磁场的旋转方向决定于通入定子绕组中的三相交流电源的相序,只要任意调换电动机( )所接交流电源的相序,旋转磁场既反转。 ___
A. 两相绕组
B. 一相绕组
C. 三相绕组
【单选题】
电烙铁用于( )导线接头等。 ___
A. 锡焊
B. 铜焊
C. 铁焊
【单选题】
螺旋式熔断器的电源进线应接在( )。 ___
A. 下端
B. 上端
C. 前端
【单选题】
引起电光性眼炎的主要原因是( )。 ___
A. 可见光
B. 红外线
C. 紫外线
【单选题】
按照计数方法,电工仪表主要分为指针式仪表和( )式仪表。 ___
A. 比较
B. 电动
C. 数字
【单选题】
使用剥线钳时应选用比导线直径( )的刃口。 ___
A. 稍大
B. 相同
C. 较大
【单选题】
更换熔体时,原则上新熔体与旧熔体的规格要( )。 ___
A. 不同
B. 相同
C. 更新
【单选题】
铁壳开关在作控制电机启动和停止时,要求额定电流要大于或等于( )倍电动机额定电流。 ___
A. 一
B. 两
C. 三
【单选题】
胶壳刀开关在接线时,电源线接在( )。 ___
A. 下端(动触点)
B. 上端(静触点)
C. 两端都可
【单选题】
电流表的符号是( ) ___
A. A
B. Ω
C. V
【单选题】
低压电工作业是指对( )V以下的电气设备进行安装、调试、运行操作等的作业。 ___
A. 500
B. 250
C. 1000
【单选题】
绝缘安全用具分为( )安全用具和辅助安全用具。 ___
A. 直接
B. 间接
C. 基本
【单选题】
下列现象中,可判定是接触不良的是( )。 ___
A. 灯泡忽明忽暗
B. 日光灯启动困难
C. 灯泡不亮
【单选题】
熔断器的额定电流( )电动机的起动电流。 ___
A. 大于
B. 等于
C. 小于
【单选题】
降压启动是指启动时降低加在电动机( )绕组上的电压,启动运转后,再使其电压恢复到额定电压正常运行。 ___
A. 定子
B. 转子
C. 定子及转子
【单选题】
特种作业操作证有效期为( )年。 ___
A. 8
B. 12
C. 6
【单选题】
电流继电器使用时其吸引线圈直接或通过电流互感器( )在被控电路中。 ___
A. 并联
B. 串联
C. 串联或并联
【单选题】
下列灯具中功率因数最高的是( )。___
A. 节能灯
B. 白炽灯
C. 日光灯
【单选题】
一般照明场所的线路允许电压损失为额定电压的( )。 ___
A. ±5%
B. ±10%
C. ±15%
【单选题】
静电防护的措施比较多,下面常用又行之有效的可消除设备外壳静电的方法是( )。 ___
A. 接零
B. 接地
C. 串接
【单选题】
三个阻值相等的电阻串联时的总电阻是并联时总电阻的( )倍。 ___
A. 6
B. 9
C. 3
【单选题】
稳压二极管的正常工作状态是( )。 ___
A. 截至状态
B. 导通状态
C. 反向击穿状态
【单选题】
( )的电机,在通电前,必须先做各绕组的绝缘电阻检查,合格后才可通电。 ___
A. 一直在用,停止没超过一天
B. 不常用,但电机刚停止不超过一天
C. 新装或未用过的
【单选题】
电容器属于( )设备。 ___
A. 危险
B. 运动
C. 静止
【单选题】
绝缘手套属于( )安全用具。 ___
A. 辅助
B. 直接
C. 基本
【单选题】
将一根导线均匀拉长为原长的 2 倍,则它的阻值为原阻值的( )倍。 ___
A. 1
B. 2
C. 4
推荐试题
【单选题】
Which command enables port security to use sticky MAC addresses on a switch?___
A. switchport port-security violation restrict
B. switchport port-security mac-address sticky
C. switchport port-security violation protect
D. switchport port-security
【单选题】
When you edit an IPS subsignature, what is the effect on the parent signature and the family of subsignatures?___
A. The change applies to the parent signature and the entire family of subsignatures
B. The change applies to the parent signature and the subsignature that you edit
C. The change applies only to subsignatures that are numbered sequentially after the subsignature that you edit
D. Other signatures are unaffected, the change applies only to the subsignature that you dit
【单选题】
Which type of mechanism does Cisco FirePOWER de ploy to protect ag detected moving across other networks?___
A. antivirus scanning
B. policy-based
C. reputation-based
D. signature-based
【单选题】
What action must you take on the ise to blacklist a wired device?___
A. Locate the switch through which the device is connected and push an a cl restricting all access by the device
B. Issue a CoA request for the de vice's mac address to each access switch in the network
C. Revoke the device's certificate so it is unable to authenticate to the network
D. Add the device's MAc address to a list of black listed devices
【单选题】
Which type of firewall can perform deep packet inspection?___
A. packet-filtering firewall
B. stateless firewall
C. application firewall
D. personal firewall
【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
2.刀开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
3.行程开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
4.交流接触器的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
A. 频繁地
B. 偶尔
C. 手动
D. 不需
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16.短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
17.一般电气控制系统中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
18.交流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电