【填空题】
65、运行中冷却装置发生周期性“喀冬喀冬”声时为液压马达___破损。
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
轴承
解析
暂无解析
相关试题
【填空题】
66、运用中对轮对检查的技术要求中规定:轮箍踏面磨耗深度不超过7mm,使用报废限度为___mm。
【填空题】
67、内燃机车车体钢结构按承载方式,一般可分为承载车体和___。
【填空题】
68、DF4B型内燃机车柴油机活塞到达下止点前___的角度时,排气阀开。
【填空题】
69、机车在运行中油水温度不得超过___ ℃。
【填空题】
70、活塞环与环槽间隙过小时,活塞与活塞环受热膨胀后易将活塞环___在槽内,使其失去弹性和工作能力。
【填空题】
71、增、减载针阀开度过大,会使柴油机有载时大幅度___。
【填空题】
72、联合调节器在补偿活塞上方压力油通路上,设有___针阀,它控制联合调节器反馈系统的工作性能,使转速调节过程更趋于稳定。
【填空题】
73、在回手柄减负荷的过程中,柴油机有“飞车”迹象时,应将主手柄___,千万不要卸掉负荷。
【填空题】
74、燃油系统的功用是保证定量、定质、___地向气缸内供给燃油。
【填空题】
75、机车运行中,柴油机油水温度应保持在___℃之间。
【填空题】
76、无级调速装置的组成为新型司机控制器、___和传动装置。
【填空题】
77、无级调速机车主手柄提升位,5、6、7、8号触头___,柴油机转速上升。
【填空题】
78、当DLS线圈通电后,动铁芯被电磁吸力吸向静铁芯并带动尾杆下移,针阀关闭___,柴油机才能正常启动。
【填空题】
79、闭合5K,辅助发电机电压显示110V,蓄电池充电电流表显示放电的原因是启动接触器QC犯卡、烧结,不能___ 。
【填空题】
80、当控制电路发生正、负两点同时接地时,将引起保险、导线、___烧损。
【填空题】
81、东风4B型机车电阻制动在柴油机-发电机组的转速一定时,制动电流不随___的变化而变化。
【填空题】
82、如因牵引发电机本身故障造成发电机不发电的原因,一般是极间连线或引出线焊接脱焊,紧固不牢或折断等;励磁线圈在正负两端处短路或___;电枢线圈断线等。
【填空题】
83、启动柴油机时,按下1QA,___线圈和1SJ得电,QBC主触头接通QBD电路,启动机油泵投入工作。
【填空题】
84、当启动发电机电压升至127V时或充电电流大于100A时,___动作,自动转入固定发电。
【填空题】
85、QBC线圈得电动作后,其主触头闭合,接通启动机油泵电动机电源,启动机油泵向___充油。
【填空题】
86、启动发电机做为发电机时分为___ 和固定发电两种工况。
【填空题】
87、列车制动机为一次缓解型时,牵引时JZ-7型空气制动机双端的客货车转换手柄必须置于___。
【填空题】
88、JZ-7型空气制动机非操纵端自阀手柄误放运转位时,当操纵端自阀施行制动时,均衡风缸减压正常,制动管___,但操纵端中继阀排风口排风不止。
【填空题】
89、JZ-7型空气制动机自阀制动,机车制动缸压力不能按比例上升,且不能保压,工作风缸指示压力下降,为___ 泄漏。
【填空题】
90、JZ-7型空气制动机自阀的重联柱塞阀是连通或切断___与中继阀的联系。
【填空题】
91、JZ-7型空气制动机分配阀变向阀柱塞卡滞在单作管侧时,自阀制动___,单阀制动无效。
【填空题】
92、JZ-7型空气制动机主阀供气阀泄漏时,自阀前四位时,主阀排气口___,手柄后三位,机车制动缸压力增至限压阀所限制的压力时,主阀排气口停止排气。
【填空题】
93、JZ-7型空气制动机单阀手柄在各位置时,单阀调整阀盖下方缺口均排风不止时,为___泄漏。
【填空题】
94、JZ-7型制动机自阀有过充位、运转位、最小减压位、最大减压位、___、手把取出位、紧急制动位七个作用位置。
【填空题】
95、JZ-7型制动机作用阀由勾贝、膜板、空心阀杆、___ 、管座等组成。
【填空题】
96、空气压缩机产生压缩空气,进入___储存,供机车空气系统各部使用。
【填空题】
97、闸瓦间隙自动调整器的功用是使闸瓦距车轮踏面的___自动保持在规定范围内。
【填空题】
98、制动管向紧急风缸充气,由制动管和紧急风缸的___控制紧急部放风阀的开启或关闭。
【填空题】
99、在静液压泵和___主轴轴承处,装有泄油管与封闭油箱相连。
【填空题】
100、柴油机增压压力不足,将使气缸内___减少,排气温度增高,增加燃油消耗。
【简答题】
5.牵引电机故障后,使用电阻制动有何危害?《机车乘务员通用知识》P33T171
【简答题】
6.什么是循环式运转方式?《机车乘务员通用知识》P43T207
【简答题】
7.确定机车交路应考虑哪些因素?《机车乘务员通用知识》P50T239
【简答题】
8.机车上的安全保护装置动作后应注意什么?《机车乘务员通用知识》P63T289
【简答题】
8.遇天气恶劣无法辨认出站(进路)信号机显示时,在列车具备发车条件后,司机应如何行车?J338
推荐试题
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
2.刀开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
3.行程开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
4.交流接触器的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
A. 频繁地
B. 偶尔
C. 手动
D. 不需
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16.短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
17.一般电气控制系统中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
18.交流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
19.直流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
20.接触器的额定电压应不小于主电路的___。
A. 短路电压
B. 工作电压
C. 最大电压
D. 峰值电压
【单选题】
21.接触器的额定电流应不小于被控电路的___。
A. 额定电流
B. 负载电流
C. 最大电流
D. 峰值电流
【单选题】
22.对于___工作制的异步电动机,热继电器不能实现可靠的过载保护。
A. 轻载
B. 半载
C. 重复短时
D. 连续
【单选题】
23.对于△接法的异步电动机应选用___结构的热继电器。
A. 四相
B. 三相
C. 两项
D. 单相
【单选题】
24.对于工作环境恶劣、启动频繁的异步电动机,所用热继电器热元件的额定电流可选为电动机额定电流的___倍。
A. 0.95~1.05
B. O.85~0.95
C. 1.05~1.15
D. 1.15~1.50
【单选题】
25.中间继电器的选用依据是控制电路的___、电流类型、所需触点的数量和容量等。
A. 短路电流
B. 电压等级
C. 阻抗大小
D. 绝缘等级
【单选题】
26中间继电器一般用于___中。
A. 网络电路
B. 无线电路
C. 主电路
D. 控制电路