【单选题】
一类、二类、应急类工作许可人应得到( )后方可进行操作。___
A. 调度部门操作指令
B. 站长指令
C. 安全员指令
D. 工作负责人指令
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
工作票所列安全措施全部操作或布置完毕后,方可许可工作,并及时向( )报告___
A. 站场值班人员
B. 站长
C. 发令人
D. 安全员
【单选题】
( )应经区域中心站同意,由工作许可人与工作负责人一同前往工作现场逐项检查核对工作票所列安全措施,经双方确认无误,方可许可工作。___
A. 三类工作
B. 二类工作
C. 一类工作
D. 应急类工作
【单选题】
工作许可后,( )应及时在工作票工作许可时间栏填写实际工作开始时间。___
A. 许可人
B. 负责人
C. 监护人
D. 站长
【单选题】
工作结束后,工作许可人应与工作负责人一同在现场检查确认安全措施已恢复至( )状态。___
A. 工作许可时
B. 备用
C. 工作许可后
D. 运行
【单选题】
工作票终结后,( )应及时向值班调度或工作许可部门报告,得到恢复输气指令后,方可进行复役操作。___
A. 站长
B. 工作许可人
C. 工作监护人
D. 工作负责人
【单选题】
( )必须在工作开始前与工作负责人共同逐项确认各项安全措施均已执行,并在工作票工作许可栏上签名后,方可允许开始工作___
A. 站场值班人员
B. 站长
C. 专职监护人
D. 工作许可人
【单选题】
输气管道线路上的工作必须明确或单独设置( ),无人监护不得工作。___
A. 监护人
B. 管理人员
C. 应急人员
D. 抢修人员
【单选题】
工作过程中发现设备设施与运行设备设施不能有效隔离的,应采取有效防范措施,并在( )现场全程监护下,方可继续工作。___
A. 专职监护人
B. 站长
C. 安全员
D. 运行人员
【单选题】
工作票风险辨识结果涉及八大特殊作业的,应同时办理( )。___
A. 特殊作业许可证
B. 动火许可证
C. 工作许可证
D. 特殊作业证
【单选题】
八大特殊作业中部分作业项目还应编制专项施工方案,方案中应有专门的()。___
A. 风险分析
B. 应急措施
C. 风险控制措施
D. 应急救援方案
【单选题】
专项施工方案应经管道企业( )组织作业部门、工作许可部门、技术管理部门、安监部门审查批准后,作为办理工作票、特殊作业许可证的依据。___
A. 分管技术领导
B. 分管安全领导
C. 分管生产领导
D. 负责人
【单选题】
管道运行压力不得大于管道企业规定的管道( )。___
A. 允许工作压力
B. 最高允许工作压力
C. 设计工作压力
D. 最高设计工作压力
【单选题】
当班调度应根据上游气源条件、下游用户需求等,调控管网的( )。___
A. 压力和温度
B. 温度和流量
C. 压力和流量
D. 压力和流速
【单选题】
( )应对安防系统进行实时监控,发现异常应及时处置。___
A. 站长
B. 安全员
C. 站场运行值班人员
D. 当班调度
【单选题】
站场运行人员应按照规定的巡视路线、频次对设备进行巡视,当远传值与就地值偏差达( )时,应及时填写缺陷单,并报告。___
A. 2%
B. 5%
C. 4%
D. 3%
【单选题】
站场运行人员应按照规定的巡视路线、频次对设备进行巡视,对站场设备的全面检漏每周不少于( )次。___
A. 4
B. 3
C. 2
D. 1
【单选题】
当上游气源短缺、管网发生故障不能满足下游用户用气需求,严重影响管网安全运行时,( )应按有序用气有关规定及时采取限供气措施,并启动相应应急预案。___
A. 调度值长
B. 当班调度
C. 值班人员
D. 中心站站长
【单选题】
各类运行原始记录应至少保留( )年。___
A. 4
B. 3
C. 2
D. 1
【单选题】
站场运行人员巡视时,应随身携带( ),特别是在进入封闭空间内巡视输气管道设备设施时,应先检测可燃气体浓度符合要求。___
A. 可燃气体检测仪
B. 氧气检测仪
C. 噪声检测仪
D. 硫化氢检测仪
【单选题】
自动监控与数据采集系统应仅限于本人操作登陆,上岗人员( ),并保证账号及密码私密性。___
A. 无需账号
B. 一人一账号
C. 一站一账号
D. 公用一个账号
【单选题】
雷雨天气必须进行( )时,不得靠近避雷器或避雷针。___
A. 室外巡视
B. 作业
C. 室外巡视或作业
D. 室内作业
【单选题】
巡视配电间时,进出房间应随手关门。发生带电设备接地时,室内不得接近故障点( )米以内。___
A. 4
B. 5
C. 2
D. 1
【单选题】
巡视配电间时,进出房间应随手关门。发生带电设备接地时,室外不得接近故障点( )米以内。___
A. 10
B. 9
C. 8
D. 5
【单选题】
站场运行人员巡视发现输气管道设备设施发生( )时,应采用肥皂水或检漏仪进行检漏,不得采用明火检漏。___
A. 大量泄漏
B. 微量泄漏
C. 泄漏
D. 漏气
【单选题】
当发现( )时,不得靠近泄漏点,应设法快速切断气源,并立即报告站场负责人和调度部门。___
A. 大量泄漏
B. 微量泄漏
C. 泄漏
D. 漏气
【单选题】
输气管道设备设施停运操作必须按照先切断进气侧、再切断出气侧和先切断( )、再切断()的顺序进行。___
A. 近设备设施侧 远设备设施侧
B. 远设备设施侧 近设备设施侧
C. 近设备设施侧 设备设施侧
D. 设备设施侧 远设备设施侧
【单选题】
操作中发生疑问或出现故障时,应立即停止操作并向( )报告,同时汇报站场负责人,待查清原因、排除故障后,方可继续操作。不得擅自更改操作项目和操作顺序。___
A. 值班调度
B. 值班人员
C. 站长
D. 工作监护人
【单选题】
操作应由( )人执行,其中对设备较为熟悉者担任监护。___
A. 4
B. 3
C. 2
D. 1
【单选题】
除( )外,所有输气管道设备设施操作均应使用操作票。___
A. 检修作业
B. 应急处置操作
C. 月度切换
D. 配合操作
【单选题】
操作票由( )填写,监护人审票,票面应清楚整洁,不得任意涂改。___
A. 值班调度
B. 值班人员
C. 操作人
D. 站长
【单选题】
( )应对照管(接)线图板或计算机上管(接)线图对操作项目进行模拟操作确认操作票正确无误后,分别在操作票上手工签名。___
A. 操作人和监护人
B. 许可人和负责人
C. 许可人和监护人
D. 操作人和负责人
【单选题】
特别重要和复杂的操作票需()或运行管理部门专工审核签名。___
A. 值班调度
B. 站场负责人
C. 部门主任
D. 调度值长
【单选题】
操作票应编号,按照编号顺序使用。作废的操作票应注明“作废”字样,已执行完毕的操作票应盖上( )章。___
A. 已完结
B. 已执行
C. 已闭环
D. 已完成
【单选题】
( )的汇报应全过程录音并做好记录。___
A. 发布指令
B. 接受指令
C. 指令执行完毕
D. 以上都是
【单选题】
正常操作应尽量避免在交接班时进行,必须在交接班时进行的操作,则由( )负责操作完毕。___
A. 站长分配
B. 交班人
C. 常白班人员
D. 以上都可以
【单选题】
管道企业应建立设备定期切换试验制度和台账,明确试验( ),并严格执行。___
A. 项目
B. 日期
C. 周期
D. A和C
【单选题】
支路切换试验过程中,应遵循( )的原则,应在备用支路投运后,方可关断在运支路___
A. 先开后关
B. 先关后开
C. 先停运后投运
D. 以上均可
【单选题】
管线打开作业前应进行可燃气体检测,必要时还应进行氮气置换,保障可燃气体浓度低于爆炸下限,同时( )应对可能残存的可燃气体或突然来气的风险进行评估,并根据风险评估结果制定相应的控制措施,必要时编制专项作业方案。___
A. 监理单位
B. 业主单位
C. 承包单位
D. 作业单位
【单选题】
在受管线打开影响的区域设置( ),控制无关人员进入。___
A. 路障
B. 警戒线
C. 路障或警戒线
D. 障碍或警戒线
【单选题】
( )前应确认集液罐液位正常并记录液位,集液罐、排污池液位超过警戒液位时,应暂停操作。___
A. 计量比对
B. 支路切换
C. 冷却置换
D. 排污操作
推荐试题
【单选题】
A VM folder contains VM1 and VM2. Group A has permission to power on virtual machines, defined on the VM folder and its children. Group B has permission to power off virtual machine VM2. If a user is a member of group A and B, what action can the user perform?___
A. Suspend VM2.
B. Power off VM1.
C. Power on and power off VM1.
D. Power on and power off VM2.
【单选题】
The networking team has requested to have a dedicated network for iSCSI traffic. This task has been assigned to the vSphere Administrator. What is the VMware-recommended way to accomplish this?___
A. Configure Static Routes on each ESXi Server.
B. Configure the right subnet.
C. Create a custom IP Stack.
D. Define a dedicated gateway for the iSCSI vmkernel.
【单选题】
To prevent possible failures or issues during a vSphere upgrade, which component should be upgraded first?___
A. ESXi Hosts
B. virtual machines
C. datastores
D. vCenter Server
【单选题】
What is the command for updating an ESXi host?___
A. esxcli software vib update –d /vmfs/volumes/Datastore/DirectoryName/PatchName.zip
B. esxupdate software update –d”/vmfs/volumes/Datastore/DirectoryName/PatchName.zip”
C. esxcli software update –d “/vmfs/volumes/Datastore/DirectoryName/PatchName.zip”
D. esxupdate software vib update –d /vmfs/volumes/Datastore/DirectoryName/PatchName.zip
【单选题】
A vSphere Administrator would like to identify which physical NUMA node their virtual machine is currently residing on. What esxtop metric would provide this information?___
A. GST_ND[x]
B. OVD_ND[x]
C. NRMEM
D. NHN
【单选题】
How can a vSphere administrator ensure that two virtual machines never run on the same datastore in a datastore cluster, while permitting the VMs to be load-balanced?___
A. Use an Intra-VM Anti-Affinity Rule.
B. Configure a storage DRS VM override.
C. Disable storage
D. RS for the VMs.
【单选题】
What is the VMware-recommended way to move a physical adapter out of Network I/O Control’s scope?___
A. Set the teaming policy to “Route Based on Physical NIC Load.”
B. Add the vmnic to the Net.NetNiocAllowOverCommit parameter in Advanced System Settings.
C. Add the vmnic to the Net.IOControlPnicOptOut parameter in Advanced System Settings.
D. Move the vmnic to a different vmUplink port on the Distributed Switch.
【单选题】
A VM folder contains VM1 and VM2. Group A has permission to power on virtual machines, defined on the VM folder and its children. Group B has permission to power off virtual machines, defined on the VM folder and its children. If a user is a member of Groups A and B, what will be the user’s effective permission on VM1 and VM2?___
A. Power on
B. Power off.
C. Power on and Power off.
D. Reset.
【单选题】
Group 1 is granted console interaction on a VM folder. User 1 is granted no console interaction on the same VM folder. What will be the outcome if User 1 tries to access the console of a virtual machine?___
A. User 1 will not be able to access the virtual machines in the VM folder.
B. User 1 will not have access to the virtual machine console.
C. User 1 will have access to the virtual machine console.
D. User 1 will have console access only via the vSphere Web Client.
【单选题】
Which statement is true regarding the use of VMFS3 datastores with vSphere 6.5?___
A. VMFS3 datastores can be used but not created.
B. VMFS3 datastores can be neither used nor created.
C. VMFS3 datastores will be present but unmounted.
D. VMFS3 datastores can be created and used.
【单选题】
In the Exhibit, each VM has a 1GHz non-expandable reservation. If all VMs are powered on in sequence, what would be the outcome?___
A. VM4 cannot be powered on.
B. VM5 cannot be powered on.
C. VM6 cannot be powered on.
D. VM3 cannot be powered on.
【单选题】
vSphere 6.5 introduced MAClearning capabilities for VMware’s virtual switches. What three benefits will it provide? (Choose three.)___
A. Reduced memory consumption.
B. Reduced consumption of extra CPU cycles.
C. Increased network throughput.
D. Prevent packet flooding inside the vSwitch.
【单选题】
What is the default pathing policy for most active-active arrays?___
A. Fixed
B. Most Recently Used
C. Dynamic
D. isk Morroring
【单选题】
Which command will show the iSCSI sessions on a ESXi 6.5 host?___
A. esxcli storage iscsi session get
B. esxcli iscsi session get
C. esxcli storage iscsi session
D. esxcli iscsi session list
【单选题】
Which of the following is not a parameter for traffic filtering or marking?___
A. virtual port ID
B. Protocol
C. Traffic Direction
D. DSCP value
E. Traffic redirection
【单选题】
A vSphere administrator wants to enable a virtual machine with Secure Boot, but in VM setting, Secure Boot option was not found under Boot Options. What could be the cause?___
A. The virtual hardware is not compatible.
B. The virtual machine has missing drivers.
C. The virtual machine OS does not support secure boot.
D. VMware Tools is not upgraded.
【单选题】
A virtual machine is connected on a distributed port group where the average bandwidth configured in the traffic shaping policy is 100 Mbps. The VM network adapter is configured with a reservation of 200 Mbps. What is the VM’s effective bandwidth?___
A. 200 Mbps
B. 100 Mbps
C. 150 Mbps
D. 400 Mbps
【多选题】
What are two reasons why a datastore in a Storage DRS cluster cannot enter maintenance mode?(Choose two.)___
A. Storage latency is too high to allow Storage DRS initiate Storage vMotion.
B. Storage DRS is configured for a VMFS3 datastore.
C. Storage
D. RS is disabled on the virtual disk.
【多选题】
What two methods are used to configure VMware vSphere Storage I/O Control shares and limits? (Choose two.)___
A. Assign shares and limits to VM virtual disks.
B. Assign shares and limits to datastores.
C. Assign shares and limits to Storage (DRS) clusters.
D. Assign shares and limits using VM storage policies.
【多选题】
ESXi 6.5 introduces VMFS6, which supports both 512e and 512n devices. What three configurations are supported when using these devices? (Choose three.) ___
A. Hosts with both 512e and 512n devices.
B. Storage vMotion between both 512e and 512n devices.
C. Datastore Extents spanned between both 512e and 512n devices.
D. Storage DRS clusters containing only both 512e and 512n devices.
【多选题】
A vSphere Administrator observes that the Primary VM configured with Fault Tolerance is executing slowly. After further investigation, it is determined that the Secondary VM is on an overcommitted ESXi host. What two methods will correct the problem? (Choose two.)___
A. Use Storage vMotion to migrate the Secondary VM to another datastore.
B. Use vMotion to migrate the Secondary VM to a different ESXi host.
C. Configure a CPU limit on the Primary VM which will also apply to the Secondary VM.
D. Turn off and turn on FT in order to recreate the Secondary VM on a different datastore.
【多选题】
Which two features require the use of Host Profiles? (Choose two.)___
A. Host Customizations
B. shared storage
C. Auto
D. eploy
【多选题】
What three processes on the vCenter Server Appliance (VCSA) does“vmware-watchdog monitor? (Choose three.) ___
A. vmware-eam
B. vmcad
C. vmware-vpostgres
D. vpxd
E. vsan-health
【多选题】
What three processes on the vCenter Server Appliance (VCSA) does“vmware-watchdog monitor? (Choose three.) ___
A. vmware-eam
B. vmcad
C. vmware-vpostgres
D. vpxd
E. vsan-health
【多选题】
Which two statements correctly describe VM-Host affinity rules? (Choose two.) ___
A. When there is more than one VM-Host affinity rule in a vSphere DRS cluster, the rules are applied equally.
B. After creating a VM-Host affinity rule, its ability to function in relation to other rules is predetermined.
C. When there is more than one VM-Host affinity rule in a vSphere
D. RS cluster, the rules will be ranked.
【多选题】
An administrator wants to enable proactive HA by moving virtual machines automatically if a hardware alert is triggered. What are the three required settings? (Choose three.)___
A. Set vSphere DRS Automation to Partially Automated.
B. Turn on Proactive HA.
C. Set the Proactive HA Automation Level to Manual.
D. Set the Proactive HA Automation Level to Automated.
E. Turn on vSphere HA and vSphere DRS.
【多选题】
If vCenter Server 5.5 installation has one or more services deployed remotely, which three services are relocated to vCenter Server 6.5 on upgrade? (Choose three.)___
A. vCenter Inventory Services
B. vSphere Authentication Proxy
C. vSphere Web Client
D. vSphere
E. SXi Dump Collector
【多选题】
What two debugging levels can a virtual machine be configured to? (Choose two.)___
A. Verbose
B. Debugging
C. Statistics
D. Trivia
【多选题】
What are three benefits of using a few large-capacity LUNs instead of many small-capacity LUNs? (Choose three.) ___
A. Better performance because there is less contention for a single volume.
B. More flexibility for resizing virtual disks.
C. Less wasted storage space.
D. More flexibility to create virtual machines without adding new LUNs.
E. Fewer VMFS datastores to manage.
【多选题】
Which two configurable options are available in Boot Options for a virtual machine? (Choose two.)___
A. Tools Upgrades
B. Encryption
C. Firmware
D. Force BIOS setup
【多选题】
Which three VMware-recommended best practices should an administrator follow before upgrading to vSphere 6.5? (Choose three.)___
A. Disconnect ESXi host from vCenter.
B. VMware Tools are installed in the virtual machine.
C. Ensure that the system hardware complies with ESXi requirements.
D. Back up the host.
E. Check the interoperability of any other software integrated with vSphere.
【多选题】
What are two requirements to enable EVC in vSphere DRS cluster? (Choose two.)___
A. CPUs must be from the same vendor.
B. EVC must use the lowest possible baseline supported by the hardware.
C. CPUs must be in the same family and of the same speed.
D. No VMs may be running in the cluster.
【多选题】
What three conditions could result in VMware Flash Read Cache being unable to claim a disk? (Choose three.)___
A. The disk is not listed in the VMware hardware compatibility guide.
B. The disk is not detected as an SSD.
C. The disk is not detected as local.
D. The disk is in use by VMFs.
【多选题】
Boot from SAN is supported on which three storage technologies? (Choose three.)___
A. VMware vSAN
B. FCoE
C. NFS 4.1
D. iSCSI
E. FC
【多选题】
Which two components are part of storage I/O multipathing on ESXi? (Choose two.)___
A. SATP
B. VASA
C. PSP
D. VAAI
【多选题】
Which two statements are true about Highly Available vSphere Auto Deploy infrastructure? (Choose two.)___
A. It helps prevent data loss.
B. It is a prerequisite for using vSphere Auto Deploy with stateful install.
C. It requires two or more Auto
D. eploy servers.
【多选题】
The virtual machine log rotation size can be changed for all VMs by which two interfaces? (Choose two.)___
A. PowerCLI
B. vSphere Web Client
C. ESXi host client
D. esxcli
【多选题】
Which two configuration options can exclude virtual disks from snapshot operations? (Choose two.)___
A. Use RDM in virtual mode for virtual disk.
B. Use virtual disks in Independent – Persistent mode.
C. Use a virtual disk larger than 2 TB in size.
D. Use RDM in physical mode for virtual disk.
【多选题】
Which two storage configurations on the source server are unsupported with VMware Converter? (Choose two.)___
A. Linux LVM
B. software RAID
C. GPT/MBR hybrid disks
D. Windows basic volumes
E. Windows dynamic volumes
【多选题】
Which two statements about vCenter HA are correct? (Choose two.)___
A. ESXi 5.5 or later is required.
B. vCenter HA network latency between nodes must be less than 50 ms.
C. NFS datastore is supported.
D. It must be deployed on a 3
E. SXi host cluster with DRS enabled.