【单选题】
划线时,在零件的每个方向都要选择( )个基准。
A. 一
B. 二
C. 三
D. 四
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
起重机试吊时,重物离地面( )后,应经过检查确认稳定可靠后方可起吊(1.0分)
A. 5米
B. 3米
C. 1米
D. 半米
【单选题】
DK-1型制动机中电空阀257为( )电空阀。(1.0分)
A. 缓解电空阀
B. 中立电空阀
C. 制动电空阀
D. 过充电空阀
【单选题】
GK型三通阀( )过弱是导致制动机自然制动主要原因。(1.0分)
A. 递动弹簧
B. 缓解弹簧
C. 蝴蝶弹簧
D. 橡胶圈
【单选题】
DK-1型制动机中缓解电空阀的代号为( )(1.0分)
A. 257
B. 252
C. 254
D. 258
【单选题】
接触网断线接地时,在切断电源前,任何人与接地点的距离,不得小于( )。(1.0分)
A. 5m
B. 8m
C. 10m
D. 12m
【单选题】
CCB-Ⅱ型制动机中TPER是指( ) 测试点(1.0分)
A. 平均管压力
B. 列车管压力
C. 总风压力
D. 均衡风缸压力
【单选题】
DK-1型制动机属于( )。(1.0分)
A. 空气制动机
B. 电空制动机
C. 真空空气制动机
D. 电阻制动机
【单选题】
机车车辆换长等于它的全长除以( )。
A. 10
B. 11
C. 12
D. 13
【单选题】
DK-1型空气制动阀设有( )个工作位置(1.0分)
A. 2
B. 3
C. 4
D. 5
【单选题】
JZ-7型空气制动机单独制动阀凸轮各位置均匀磨耗量不得大于( )。
A. 0.6mm
B. 0.5mm
C. 0.3mm
D. 0.4mm
【单选题】
过盈连接是依靠孔、轴配合后的()来达到坚固连接的。(1.0分)
A. 摩擦力
B. 压力
C. 拉力
D. 过盈值
【单选题】
下列不属于高度调整阀试验项目的是( )。(1.0分)
A. 无感带区试验
B. 作用延迟时间试验
C. 极限作用试验
D. 空气流量试验
【单选题】
JZ-7型空气制动机单独制动阀手柄由全制动位快速移回运转位,作用管压力由300降到35kPa的时间应在( )以内。
A. 5s
B. 4s
C. 2s
D. 6s
【单选题】
用百分表测量时,测量杆应预先压缩0.3~1mm,以保证一定的初始测量力,以免( )测不出来。(1.0分)
A. 公差
B. 形状公差
C. 负偏差
D. 尺寸
【单选题】
改善低碳钢的切削加工性,应采用( )处理。(1.0分)
A. 正火
B. 退火
C. 回火
D. 淬火
【单选题】
列车由甲地到乙地运行的平均速度称为( )。(1.0分)
A. 构造速度
B. 技术速度
C. 旅行速度
D. 限制速度
【单选题】
一定量的气体在同等环境下,存储容器容积越大,其压力( )。(1.0分)
A. 越小
B. 越大
C. 不变
D. 两者无关
【单选题】
按不同的弦长等分圆周,会减少累积( )。(1.0分)
A. 偏差
B. 公差
C. 误差
D. 上偏差
【单选题】
JZ-7型空气制动机自动制动阀性能试验中,手柄移置紧急制动位列车管压力降到0的时间不超过()。
A. 7s
B. 3s
C. 2s
D. 6s
【单选题】
均衡风缸和列车管减压停止时,列车( )。(1.0分)
A. 制动
B. 缓解
C. 制动保压
D. 运行
【单选题】
按规定的技术要求,将若干零件组合成( )或将若干零件和部件组合成机器的过程称为装配。(1.0分)
A. 组件
B. 部件
C. 一级组件
D. 机器
【单选题】
JZ-7型空气制动机无动力装置由阻流塞、止回阀弹簧、截断塞门、( )组成。(1.0分)
A. 止回阀座
B. 滤尘器
C. 止回阀
D. 以上均是
【单选题】
JZ-7型空气制动机自动制动阀泄漏试验中,列车管压力( )内不得下降。(1.0分)
A. 1min
B. 2min
C. 0.5min
D. 1.5min
【单选题】
104 型空气制动机稳定性标准规定:单车试验时,当制动管压力达到定压后,在制动管每分钟减压( )的速度下,制动机不应发生制动作用。(1.0分)
A. 30kpa
B. 35kpa
C. 40kpa
D. 50kpa
【单选题】
弯制直缝焊接钢管时,其焊缝应放置在( )。(1.0分)
A. 外层
B. 内层
C. 中性层
D. 任意位置
【单选题】
JZ-7型空气制动机作用管( )压力空气时,作用阀呈缓解位,机车缓解。(1.0分)
A. 增压
B. 充入
C. 压缩
D. 排出
【单选题】
CCB-Ⅱ型制动机自阀设有( )个位置。(1.0分)
A. 5
B. 6
C. 7
D. 8
【单选题】
铰削余量的确定还要考虑铰孔的( )。(1.0分)
A. 环境
B. 工艺过程
C. 工件形状
D. 孔的位置
【单选题】
DK-1型制动机双阀口式中继阀主要是用来控制( )。(1.0分)
A. 列车管充气和排气
B. 均衡风缸充气和排气
C. 制动缸的充气和排气
D. 作用管的充气和排气
【单选题】
立钻主轴变速或自动进给时,必须在( )进行调整。(1.0分)
A. 转动时
B. 停车后
C. 空转时
D. 负荷后
【单选题】
圆柱孔轴承的拆卸,可以用压力机,也可以用( )(1.0分)
A. 套筒
B. 拉出器
C. 手锤
D. 软金属棒和手锤
【单选题】
HT200牌号中的200表示( )强度为200 N/mm2。(1.0分)
A. 最低抗拉
B. 最高抗拉
C. 最低抗压
D. 最低抗弯
【单选题】
DK-1型制动机调压阀将压力调整到( )kPa,送往均衡风缸和所需管路。(1.0分)
A. 300~400kPa
B. 600~700kPa
C. 500~600kPa
D. 400~500kPa
【单选题】
职业选择的意义是( )。 (1.0分)
A. 职业选择意味着可以不断变换工作岗位
B. 提倡自由选择职业会导致无政府主义
C. 职业选择有利于个人自由的无限扩展
D. 职业选择有利于促进人的全面发展
【单选题】
加热拆卸要注意的关键问题是加热温度,有变形要求的不超过120℃,有时还要对不应热膨胀的部位用( )加以保护。(1.0分)
A. 塑料
B. 橡胶
C. 石棉
D. 水
【单选题】
工具摆放要( )。(1.0分)
A. 整齐
B. 堆放
C. 混乱
D. 随便
【单选题】
钳工工作台对面有人工作时,必须设置密度( )的安全网。(1.0分)
A. 较大
B. 较小
C. 适当
D. 很小
【单选题】
DF4型机车撒砂装置主要由砂箱、( )、撒砂作用阀组成。(1.0分)
A. 撒砂阀
B. 作用阀
C. 分配阀
D. 中继阀
【单选题】
当有人触电而停止了呼吸,但心脏仍跳动时,应采取的急救措施是( )。(1.0分)
A. 立即送医院抢救
B. 请医生抢救
C. 就地立即作人工呼吸
D. 作胸外按压
【单选题】
为保证人身安全,任何人员所携带的物件(如长杆、导线等)与接触网设备的带电部分需保持( )以上的距离。
A. 1m
B. 2m
C. 3m
D. 5m
推荐试题
【多选题】
Which two components can be used when configuring Enhanced Linked Mode? (Choose two.)___
A. vCenter Server Appliance
B. vRealize Operations Manager
C. vSphere Management Appliance
D. vCenter Server for Windows
【多选题】
An organization has a number of virtual machines that would benefit from Fault Tolerance. These include: <A single vCPU Apache Server> < A dual vCPU vCenter Server> < A quad vCPU SQL Server> <An eight vCPU Hadoop Server>. Which two virtual machines can be configured to use VMware Fault Tolerance? (Choose two.)___
A. Apache Server
B. vCenter Server
C. SQL Server
D. Hadoop Server
【多选题】
Which two badges are major badges in vRealize Operations? (Choose two.)___
A. Risk
B. Efficency
C. Workload
D. Faults
【多选题】
An administrator is deploying multiple Windows 2003 Virtual Machines from the same template. What two steps should be taken to avoid network conflicts? (Choose two.)___
A. Customize the guest operating system.
B. Install VMware Tools into the new virtual machines.
C. Copy the Microsoft Sysprep tools onto the vCenter Server system.
D. Ensure the e1000 vmnic is selected for each new virtual machine.
【多选题】
Which three conditions would prevent Storage I/O Control from being enabled on a group of datastores? (Choose three.)___
A. The datastores planned for the solution are used by different vSphere clusters.
B. A datastore planned for the solution is configured as a Raw Device Mapping file.
C. A datastore planned for the solution has three extents.
D. A datastore planned for the solution is configured as NFS.
E. The organization has an Enterprise license.
【多选题】
Which two actions are prerequisites to adding ESXi 6.x hosts to a vSphere Distributed Switch? (Choose two.)___
A. Verify that there is at least one Distributed Port Group on the Distributed Switch.
B. Verify that the Distributed Port Group have active uplinks configured in its teaming and failover policy.
C. Verify that the
D. istributed Switch has been configured with a Network Profile.
【多选题】
An organization has configured Distributed Power Management (DPM) on a vSphere 6 cluster. The organization wants to be alerted when an ESXi host has been powered down by DPM. Which two options represent the type and name of the alarm that would accomplish this? (Choose two.)___
A. DrsEnteringStandbyModeEvent
B. DrsEnteredStandbyModeEvent
C. Event-based
D. Condition-based
【多选题】
Which two allow for the disabling of Network Rollback operations? (Choose two.)___
A. Modifying the vpxd advanded configuration options and adding the config.vpxd.network.rollback key
B. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\vpxd.cfg file and adjusting the<rollback> xml tag
C. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\vpxd.cfg file and adjusting the <networkrollback> xml tag
D. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\firstboot\vpxd-service- spec.prop file and adjusting the <rollback> xml tag
【多选题】
An administrator is tasked with performing a vMotion migration of a virtual machine. The virtual machine is configured as follows: <vSphere Flash Read Cache (vFRC) enabled> <Is part of a Distributed Resource Cluster (DRS) Cluster> Which two statements are true? (Choose two.)___
A. Each ESXi host in the cluster supports multiple virtual flash resources.
B. Each ESXi host in the cluster supports one virtual flash resource.
C. DRS treats powered-on virtual machines with Flash Read Cache as having a preferred affinity to their current host and moves them only for mandatory reasons.
D. DRS treats powered-on virtual machines with Flash Read Cache as having a required affinity to their current host and does not move them.
【多选题】
An administrator is using the Host Failures to Tolerate Admission Control Policy for a vSphere High Availability ___ cluster. When configuring this setting on the cluster, the administrator sees this error message: <Insufficient resources to satisfy HA failover level on cluster > What are two likely causes for the error? (Choose two.)(AB)
A. The hosts in the cluster are disconnected.
B. A host in the cluster is displaying an HA error.
C.
D. istributed Resource Scheduler has not been configured on the cluster.
【多选题】
What are two ways to identify TCP/IP stack information? (Choose two.)___
A. Using the vSphere Web Client
B. Using esxcli network ip netstack
C. Using esxcfg-netstack
D. Using the vSphere Client
【多选题】
Which two actions are required when enabling vFlash Read Cache for a virtual machine's virtual disk? (Choose two.)___
A. A value in the Virtual Flash Read Cache text box must be entered.
B. A Flash Resource Pool for Cache size reservation must be entered.
C. The Device backing and the block size must be configured.
D. The
E. nable virtual flash host swap cache check box must be selected.
【多选题】
What two IT infrastructure components are virtualized by vSphere Essentials? (Choose two.)___
A. Networks
B. Applications
C. Storage
D. Management
【多选题】
When attempting to access a virtual machine, an administrator is unable to login using the vSphere credentials. What two options are probable causes of the authentication failure? (Choose two.)___
A. The vSphere credentials have not been granted permissions.
B. The vSphere credentials are granted read-only permissions.
C. The vSphere credentials are granted no-access permissions.
D. The vSphere credentials are not a member of the local administrator group.
【多选题】
An administrator is performing a scripted installation of ESXi 6.x. In which three locations does the script need to be? (Choose three.)___
A. PXE Server
B. HTTPS
C. FTP
D. NFS
E. VVOLs Datastore
【多选题】
In order for a company to meet regulatory requirements, all ESXi 6.x Hosts must be configured to direct logs to a syslog server. What are two ways ESXi hosts can configured for this action? (Choose two)___
A. Use the esxcli system syslog command.
B. Edit them in the ESXi host Advanced System Settings.
C. From the Syslog collector user interface of the Web Client.
D. Syslog logging is not available for
E. SXi Hosts.
【多选题】
Which three actions can be executed when an alarm is triggered? (Choose three.)___
A. Send an email.
B. Send an SNMP trap.
C. Run a script or command.
D. Run an Orchestrator workflow.
E. Send a trigger to syslog.
【多选题】
An administrator is attempting to power on a virtual machine, but is unable to do so. Which two reasons are probable causes of the failure? (Choose two.)___
A. Storage access to the virtual machine swap file has been lost.
B. One of the virtual machine VMDK files is locked.
C. Virtual machine is running CentOS 7.0 64-bit.
D. Virtual machine has Hyper-Threading enabled.
【多选题】
An administrator has configured a host profile so that ESXi 6.x hosts will point to the corporate NTP server for time synchronization. The NTP server is located at 10.0.30.213, but time has not been synchronized properly across the ESXi hosts. The administrator reviews Host Profile settings as shown in the Exhibit. Which two steps are required to resolve the issue? (Choose two.)___
A. Correct the NTP server IP address.
B. Check the host for host profile compliance.
C. Remediate the host based on the updated host profile.
D. Change the NTP server to the FQDN as IP Addresses are not supported.
【多选题】
An administrator is attempting to migrate a large Hadoop virtual machine using vMotion. The administrator notices a delay when the machine is quiesced. The Hadoop virtual machine is processing many transactions a second to an in-memory database. Which two actions would help reduce the amount of time needed to perform a vMotion on this virtual machine? (Choose two.)___
A. Use multiple NICs for the vMotion vmkernel port.
B. Use a 10Gbps Network card for the vMotion vmkernel port.
C. Add an additional management network to help transmit the data quicker.
D. Disable Fault Tolerance before performing the vMotion.
【多选题】
An administrator is installing a new network card in an ESXi 6.x host that is part of a vSphere cluster. When the host is placed into maintenance mode, the vSphere Web Client displays the progress bar at 2% for over 30 minutes. Which two are likely reasons for this occurrence? (Choose two.)___
A. Maintenance mode is unable to migrate all virtual machines from the host.
B. There is a large number of virtual machines that must be migrated from the host.
C. VMware High Availability is in the process of reconfiguring the cluster.
D. Each virtual machine on the
E. SXi host must be reconfigured to recognize the new adapter.
【多选题】
Which two events happen when Distributed Resource Scheduler (DRS) is disabled? (Choose two.)___
A. The cluster's resource pool heirarchy and affinity rules are re-established when DRS is turned back on.
B. The cluster's resource pool hierarchy and affinity rules are not re-established when DRS is turned back on.
C. The cluster's resource pools are removed from the cluster.
D. The cluster's resource pools are removed from the cluster and assigned to the hosts.
【多选题】
Which two networking connection types can be configured on a virtual switch? (Choose two.)___
A. Virtual machine portgroups
B. VMkernel services (such as NFS, iSCSI, or vMotion) to the physical network
C. Web services over the Management Network
D. NFS and FCoE storage services
【多选题】
An administrator creates a DRS cluster of eight ESXi 6.x hosts. There are 10 virtual machines balanced across the hosts. An attempt to place the first host into maintenance mode fails. What are two reasons that the host failed to enter maintenance mode? (Choose two.)___
A. The DRS cluster Automation Level is set to Partially Automated mode.
B. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Should run on hosts in group.
C. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Must run on hosts in group.
D. One of the virtual machines on the
E. SXi Host entering maintenance mode is configured with an individual Automation Level set to Partially Automated.
【多选题】
When modifying a vApp, which two vSphere entities can be added? (Choose two.)___
A. A resource pool
B. A network pool
C. A vApp
D. A folder
【多选题】
From which two locations in the inventory hierarchy can you deploy a virtual machine using a template? (Choose two.)___
A. Directly from the template.
B. From a compute resource.
C. From an existing virtual machine.
D. From a Datastore.
【多选题】
A company has decided to implement Virtual SAN within their vSphere 6.x environment. The Virtual SAN cluster will be composed of three ESXi 6.x hosts that are on the Virtual SAN Ready Node list. Each ESXi host includes: <Two SAS Controllers that support Passthrough Mode> < Four Solid State Drives (SSDs) 1TB in size each> <20 SAS Magnetic Disks (MDs) 1TB in size each> <The SSDs and MDs are evenly split between the two SAS controllers>. The company will pilot a Virtual SAN cluster utilizing VMware best practices while maximizing storage capacity. The Virtual SAN cluster will use Manual Mode. Which two Disk Group configurations would meet the stated configuration requirements? (Choose two.)___
A. 4 disk groups with 1 SSD and 5 MDs each
B. 2 disk groups with 1 SSD and 7 MDs each
C. 2 disk groups with 2 SSDs and 7 MDs each
D. 2 disk groups with 1 SSD and 10 MDs each
【多选题】
A physical Windows 2008 R2 Server is converted to a virtual machine using VMware vCenter Converter. Upon completion of the conversion and subsequent power on operation, the virtual machine fails to boot and the message below is observed in the Console of the virtual machine: <STOP 0x0000007B INACCESSIBLE_BOOT_DEVICE>. Which two potential issues may be causing this boot failure? (Choose two.)___
A. An incorrect SCSI controller was selected during conversion.
B. Incompatible software drivers were migrated into the virtual machine from the source machine.
C. The vmdk file backing the virtual machine was thick provisioned.
D. A snapshot was taken immediately after the conversion completed.
【多选题】
An administrator is configuring the Failover Order option on a vSphere Distributed Switch. Which two options should be used with IP-hash load balancing? (Choose two.)___
A. Active Uplinks
B. Standby Uplinks
C. Unused Uplinks
D. Override Failover Order
【多选题】
An administrator is configuring the Maximum Transmission Unit value on a vSphere Distributed Switch. Which two options are typical values for ESXi networking? (Choose two.)___
A. 1492
B. 1500
C. 9000
D. 9089
【多选题】
Which two configurable options apply to both virtual machine CPU and memory allocation? (Choose two.)___
A. Reservation
B. Shares
C. Resource Pool
D. Reserve All
【多选题】
When attempting to power on a Virtual Machine you observe the following error: <Cannot open the disk '/vmfs/volumes/volume/vm/vm-000002.vmdk' or one of the snapshot disks it depends on.> Which three actions will be the best solutions to address this problem? (Choose three.)___
A. Verify that the virtual machine's disk files are present.
B. Investigate the host and virtual machine log files.
C. Verify the vmdk descriptor files and if required, recreate them.
D. Delete the disk file preventing the power on operation.
E. Migrate or register the virtual machine to a different host.
【多选题】
An administrator has been tasked with enabling High Availability ___ on a cluster in a vSphere 6.x environment with default settings. The cluster configures properly and there are no errors. The next day when powering on a virtual machine, an error is presented: <Not Enough Failover Resources>. Which three scenarios are likely causes of this error message? (Choose three.)(CDE)
A. The default VM Monitoring Sensitivity is set too high.
B. There are not enough datastore heartbeat datastores configured by default.
C. The default slot size in the cluster is set too high.
D. There are virtual machines with large CPU reservations.
E. A host is in maintenance mode for a replacement of a failed Hard Drive.
【多选题】
vMotion can be performed between which three physical boundaries? (Choose three.)___
A. Between two vCenter Server Systems
B. Between two vSphere Distributed Virtual Switches
C. Between two vCenter Server Datacenter objects
D. Between two VMware NSX Layer 4 segments
E. Between two NFS datastores
【多选题】
An administrator configures vSphere Replication for a virtual machine and enables multiple point in time (PIT) instances under the recovery settings in the Configure Replication wizard. Which two statements are correct for vSphere Replication with multiple point in time instances enabled? (Choose two.)___
A. vSphere Replication retains a number of snapshot instances of the virtual machine on the target site based on the retention policy that you specify.
B. vSphere Replication uses the virtual machine's snapshot instances to define the target site Point in Time instance based on the retention policy that you specify.
C. vSphere Replication does not support virtual machines with snapshots.
D. vSphere Replication supports virtual machines with snapshots.
【多选题】
An administrator is virtualizing a physical application server and adding it to an existing multi-tiered vApp. The application license is currently tied to the physical NIC's MAC address, so the administrator needs to ensure the license will function properly in the virtual machine. Which two actions can the administrator take to satisfy this task? (Choose two.)___
A. Set the MAC address for the vNIC in the guest operating system.
B. Install the physical server's NIC into the ESXi host.
C. Configure the MAC address for the vNIC using the vSphere Web Client.
D. Assign the physical server NIC's MAC address in the vSphere Distributed Switch.
【多选题】
Which two Fibre Channel zoning options are supported with vSphere 6.x? (Choose two.)___
A. Single-Initiator
B. Single-Initiator-Single-Target
C. Multiple-Initiators-Single-Target
D. Multiple-Initiators-Multiple-Targets
【多选题】
An administrator is attempting to remove an ESXi 6.x host from a vSphere Distributed Switch (vDS). When the administrator attempts to remove the host, the following error is observed: <The resource '16' is still in use.> What three steps are needed to successfully remove the host from the switch? (Choose three.)___
A. Select Manage Ports on the vDS for the host.
B. Locate all ports currently in use on the vDS for the host.
C. Migrate or delete any vmkernel or virtual machine adapters associated with the switch.
D. Remove all network cards from the switch before trying to remove the host.
E. Create a standard switch for everything to be automatically be migrated to.
【多选题】
Which two Virtual SAN related actions might start resynchronization of virtual machine objects? (Choose two.)___
A. Editing a virtual machine storage policy to increase the number of replicas.
B. Editing a virtual machine storage policy to reduce the number of replicas.
C. Editing a virtual machine storage policy to increase the number of disk stripes.
D. Editing a virtual machine storage policy to reduce the number of disk stripes.
【多选题】
An administrator is troubleshooting basic network connectivity issues. Which two scenarios are potential issues that this administrator might face? (Choose two.)___
A. The vSwitch is not attached to the correct physical network.
B. The portgroup is not configured to use correct VLAN.
C. Traffic shaping is configured incorrectly.
D. Jumbo frames is configured incorrectly.