【单选题】
攻螺纹时应使用___以减小摩擦。
A. 冷却液
B. 水
C. 酒精
D. 润滑油
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
全面质量管理的主要特点是突出“___”字。
A. 新
B. 全
C. 质
D. 管
【单选题】
___决定了相关总成、部件和汽车的工作平衡程度。
A. 振动
B. 噪声
C. 总成清洁度
D. 动、静平衡程度
【单选题】
在轻型车排放物中CO,含量不大于___。
A. 4.5%
B. 6%
C. 7%
D. 8%
【单选题】
某一汽车零件的修理工艺规程的最佳方案有___。
A. 一个
B. 多个
C. 两个
D. 无
【单选题】
确定汽车修理工艺规程的原则,关于技术上的先进性,甲说:“要尽量用新技术新工艺,采用先进检测手段,要不断增强自动化程度”;乙说:“不论条件,优先使用新技术新工艺”。说法不正确的是___。
A. 甲
B. 乙
C. 甲和乙
D. 甲和乙都不正确
【单选题】
汽车主要零件的修复方法有机械加工法、焊接法、振动堆焊法、电镀、刷镀、喷涂、电火花加工以及___。
A. 粘结法
B. 局部更换法
C. 调整翻转法
D. 压力加工修复法
【单选题】
发动机气门导管与承孔的配合过盈一般为___ mm。
A. 0.01~0.04?
B. 0.02~0.06
C. 0.025~0.085
D. 0.05~0.10
【单选题】
→___→精机械加工。
A. 喷丸处理
B. 表面热处理
C. 镀络
D. 喷涂处理
【单选题】
发动机曲轴材料要求较高的耐疲劳强度和耐磨性,轴颈表面要经过___。
A. 氮化和高频淬火
B. 正火
C. 回火
D. 退火
【单选题】
画零件工作图的步骤是:选择比例、幅面,画底图,___,描深,审核。
A. 校核
B. 选择基准
C. 画结构形状
D. 标注尺寸
【单选题】
CB-9型微机车轮动平衡测试仪的显示控制部分,工作启动键是___。
A. “START”
B. “STOP”
C. “STATIC”
D. “TEST”
【单选题】
承修车辆多、车型较单一的汽车修理厂应采用___劳动组织形式。
A. 综合作业法
B. 专业分工作业法
C. 就车修理法
D. 固定修理法
【单选题】
汽车零件分类的主要依据是___。
A. 尺寸、形位误差、表面质量
B. 尺寸、形状
C. 材料性能、尺寸、形状
D. 硬度、位置误差
【单选题】
奥迪A6发动机ATX和APS的曲轴修理尺寸有___级,级差为 0.25mm。
A. 2
B. 3
C. 4
D. 6
【单选题】
曲轴弯曲常采用冷压校正法,校正后还应进行___。
A. 时效处理
B. 淬水处理
C. 正火处理
D. 表面热处理
【单选题】
从事中型、重型汽车驱动桥维修作业,必不可少的拆装设备是___。
A. 举升架
B. 半轴套管拆装机
C. 零件清洗机
D. 光磨机
【单选题】
发动机铝制缸盖清除积炭溶液中不得加入的配方是___。
A. 肥皂
B. 重铬酸钾
C. 水玻璃
D. 苛性钠
【单选题】
汽车零件修复,下列选项中,___不是用镶套法进行的。
A. 转向节
B. 气门座
C. 发动机缸套
D. 传动轴万向节轴承座孔
【单选题】
装配尺寸链中,增环属于___。
A. 组成环
B. 减环
C. 补偿环
D. 封闭环
【单选题】
桑塔纳2000型轿车AFE发动机曲轴轴向间隙为___ mm。
A. 0.07~0.17
B. 0.10~0.25
C. 0.15~0.25
D. 0.05~0.10
【单选题】
利用拉线法检查汽车前轴时,若拉线偏离了钢板弹簧座中心,表明前轴存在___变形。
A. 水平方向的弯曲或扭曲
B. 水平方向的弯曲
C. 扭曲
D. 垂直方向的弯曲
【单选题】
在检修机械循环球式转向器,装复螺杆螺母时,甲说:“两组钢球应成组交换装入导管螺纹孔”;乙说:“两组钢球放在一起挑选分组装入导管螺纹孔”;丙说:“两组钢球应分别装入原来的导管螺纹孔”。说法正确的是___。
A. 甲
B. 乙
C. 丙
D. 甲和乙
【单选题】
检验奥迪自动变速器输出轴力矩时,如转动力矩过小,则换装一个较原厚度薄约___ mm的调整垫片 。
A. 0.05
B. 0.08
C. 0.10
D. 0.15
【单选题】
关于发动机活塞环与活塞组装,甲说:“应注意活塞环的安装方向,各气环开口角度要均匀”;乙说:“装油环时一般先装中间衬环”;丙说:“组合油环上下刮片开口应错开120°”。说法正确的是___。
A. 甲
B. 乙
C. 丙
D. 甲和乙
【单选题】
关于总成送修,甲说:“总成送修时,应在装合状态,零件不能短缺”;乙说:“承修和送修双方没必要签订合同”。说法正确是___。
A. 甲
B. 乙
C. 甲和乙
D. 甲和乙均不正确
【单选题】
汽车进厂首先要向驾驶员查询车况,下列项目中要查询的是___。
A. 车容
B. 轮胎
C. 全车电气
D. 该车历次维修内容
【单选题】
发动机连杆轴承轴向间隙使用极限为___ mm。
A. 0.40
B. 0.50
C. 0.30
D. 0.60
【单选题】
汽车发动机飞轮齿圈配合过量盈应为___ mm。
A. -0.15~-0.10
B. -0.40~-0.20
C. -0.64~-0.25
D. -0.25~-0.05
【单选题】
柴油机活塞座孔与活塞销的配合过盈是___ mm。
A. 0.0050~0.0075
B. 0.0015~0.0050
C. 0.002~0.004
D. 0.0025~0.0075
【单选题】
汽车路试前的检验必须加足的是___。
A. 润滑油、油脂、冷却液、制动液、电解液
B. 冷却液、制动液、电解液
C. 制动液、电解液
D. 润滑油、油脂、冷却液
【单选题】
汽车大修合格证应有___。
A. 检验记录
B. 走合期规定
C. 技术状况说明
D. 处理意见
【单选题】
根据客车质量检查评定方法得分值为80,应评定为___等级。
A. 一等
B. 合格
C. 不合格
D. 优良
【单选题】
汽车-25号冷动液的pH值应为 ___。
A. 7.5~11.0
B. 11.0~12.5
C. 7.5~8.5
D. 5.5~12.5
【单选题】
按照ECE1504法规规定的汽车型式认证试验,基准质量Rm≤1020kg的CO排放极限值应为___g。
A. 70
B. 80
C. 90
D. 60
【单选题】
发动机负荷对汽油机燃烧___。
A. 影响较大
B. 无影响
C. 影响较小
D. 可能有影响
【单选题】
柴油机在进气行程进入汽缸的是___。
A. 混合气
B. 纯空气
C. 先空气后混合气
D. 雾化的柴油
【单选题】
在相同的发动机功率下,车速越高汽车驱动力___。
A. 越大
B. 越小
C. 不变
D. 无法确定
【单选题】
在紧急制动时,___情况最危险。
A. 前轮先于后轮抱死
B. 后轮先于前轮抱死
C. 前后轮滑移率很小时
D. 车轮将要抱死时
【单选题】
汽车制动器制动力___。
A. 随踏板力增加而增加
B. 与地面制动力同步增长
C. 与附着力有关
D. 始终小于附着力
【单选题】
下列选项中,可作为汽车制动效能评价指标的是___。
A. 制动距离
B. 制动释放时间
C. 制动时间
D. 制动协调时间
推荐试题
【单选题】
“Deteriorating weather”means the weather is getting______.___
A. better
B. clear
C. good
D. worse
【单选题】
Azimuth means horizontal______or direction. ___
A. heading
B. direction
C. bearing
D. scale
【单选题】
According to characters and conditions of flights on the route,ATS route is divided into______and______route. ___
A. domestic,international
B. fixed,temporary
C. regional,national
D. civil,military
【单选题】
Fuel______means the quantity of fuel carried by now. ___
A. reminding
B. endurance
C. number
D. total
【单选题】
The opposite meaning of“speedup”is_________
A. slowdown
B. speeddown
C. speedlow
D. slowby
【单选题】
Pilot turns on squawk______to request a squawk number. ___
A. 3000
B. 3500
C. 4000
D. 2000
【单选题】
First______assistance means doctor and ambulance in an emergency condition. ___
A. emergency
B. priority
C. aid
D. help
【单选题】
When somebody is reported hurt on board,maybe it will need______assistance on arrival. ___
A. fire-cart
B. medical
C. police
D. wheelchair
【单选题】
In emergency descent procedure,the pilot should turn right______out of the route while descending. ___
A. 40°
B. 30°
C. 20器
D. 15°
【单选题】
管制员在对空指挥过程中,越是繁忙的时候,语速应___
A. 保持平稳,避免频繁重复指令
B. 尽量快些,才能指挥更多飞机
C. 降低语速,避免口误
D. 时快时慢,引起机组的注意
【单选题】
According to ICAO,a standard holding pattern should all turn to the______.___
A. right
B. west
C. left
D. east
【单选题】
The standard altimeter setting is______inhpa. ___
A. 1013.20062
B. 1010.10062
C. 29.92002
D. 30.10002
【单选题】
2500f/m rate of vertical speed is equal to______.___
A. 10m/s
B. 15m/s
C. 20m/s
D. 25m/s
【单选题】
陆空通话时,什么时候推荐使用“IMMEDIATELY(立即)”这个词:___
A. 相对飞行穿高度时
B. 天气差时,担心自己会忘记某个正在改变高度的动态
C. 飞机多时,为了节省精力
D. 在紧急情况下,用于冲突解脱时
【单选题】
Standard rate for a turning is______degrees per second. ___
A. 4
B. 6
C. 3
D. 2
【单选题】
What is the best course of action for a pilot to follow when thunderstorms are observed along the route of flight? ___
A. Fly below the thunderstorms
B. Climb over the thunderstorms
C. Disregard the thunderstorms
D. Take any action to avoid all thunderstorms
【单选题】
The subdivision of frequencies is______MHZ. ___
A. 0.025
B. 0.035
C. 0.02
D. 0.015
【单选题】
Aeronautical chart is divided into two categories,______. ___
A. Aeronautical map and special type of aeronautical chart
B. En-route chart and approach chart
C. Area chart and standard instrument arrival and departure chart
D. Aerodrome chart and area chart
【单选题】
Aircraft are required to comply with ATC instructions within______.___
A. advisory airspace
B. domestic airspace
C. controlled airspace
D. international airspace
【单选题】
Amendments to the initial clearance will be issued at anytime an air traffic controller deems such action necessary to______.___
A. avoid possible confliction between aircraft
B. correct the previously issued clearance
C. cancel the flight plan
D. expedite the traffic
【单选题】
研究表明,当耳机话筒的位置距离嘴( )英寸且稍微偏下时,传输的声音质量最佳。(注:1英寸=2.54CM)___
A. 0.25-0.5
B. 0.75-1
C. 1.25-1.5
D. 1.75-2
【单选题】
“I want to divert to shanghai” is equal to______.___
A. I want to our destination Shanghai
B. I want to overfly Shanghai
C. I want to alternate to land at Shanghai
D. I want to call Shanghai control
【单选题】
When an aircraft is being subjected to unlawful interference, the pilot should try to notify _______ of this fact.___
A. the appropriate ATC units
B. company
C. the passengers on board
D. air attendants
【单选题】
When pilot say“Did you pick it upon your screen?”,that means______.___
A. did you pick up your screen?
B. did you see it on your screen?
C. did your screen pick me up?
D. did you change your radar?
【单选题】
ATC clearance does not contain______.___
A. clearance limit
B. altitude data
C. route of flight
D. flight direction
【单选题】
When pilot sets an altimeter setting to a QNH,that will indicate_________
A. flight level
B. altitude
C. height
D. safety level
【单选题】
When pilots set a pressure of 29.92 in mercury to indicate_________
A. altitude
B. height
C. flight level
D. safety level
【单选题】
管制员还应当对管制指令当中的不同内容进行适当的排序,相对重要的内容应当排列在管制指令的 ( )位置___
A. 前面
B. 中间
C. 尾部
D. 以上都可以
【单选题】
When Beijing time is 0801,Zulu time should be______.___
A. 2001
B. 1
C. 601
D. 1601
【单选题】
Emergency frequency is______.___
A. 121.5MHZ
B. 120.5MHZ
C. 121MHZ
D. 119.0MHZ
【单选题】
“PAN” is the international RTF______signal___
A. emergency
B. distress
C. urgency
D. dangerous
【单选题】
“MAYDAY” is the international RTF______signal.___
A. emergency
B. distress
C. urgency
D. dangerous
【单选题】
According to ICAO definition, a condition concerning the safety of an aircraft or other vehicle or of some person on board or within sight but which does not require immediate assistance is _______ .___
A. urgency
B. dangerous
C. emergency
D. distress
【单选题】
Which SSR Code is not right?___
A. 7020
B. 8025
C. 6060
D. 4021
【单选题】
______is the accepted standard for worldwide time signal broadcast used for aviation.___
A. GMT
B. LT
C. UTC
D. SST
【单选题】
_____means the level is measured in 1013.2 pha___
A. Level
B. Height
C. Altitude
D. Flight level
【单选题】
An aircraft known or believed to be in a state of emergency should be given______over other aircraft.___
A. way
B. flight plan
C. instruction
D. priority
【单选题】
管制话筒正确使用方法是:___
A. PTT发射键还没有完全按下时就开始发指令
B. 指令还没有结束就松开PTT发射键
C. 按PTT发射键与发话同时进行,松开PTT发射键与发话同时进行
D. 先按下话筒PTT发射键,然后再开始对空发话,发话完毕后再松开话筒PTT发射键
【单选题】
SSR code is a______digital number.___
A. two
B. six
C. one
D. four
【单选题】
Traffic information should include_________
A. direction of aircraft concerned
B. weather
C. speed of aircraft
D. heading of aircraft