【多选题】
减少装置电耗,正常的方法有___
A. 合理降低鼓风机出口压力    
B. 关小泵出口阀,降低机泵电流
C. 合理降低鼓风机放空
D. 夏季延后开启装置照明用电
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
ACD
解析
暂无解析
相关试题
【多选题】
离心泵抽空时的现象是___。
A. 电机的电流上升
B. 泵出口压力表指示下降
C. 有特殊的响声
D. 泵体振动
【多选题】
安全阀常见的故障有___。
A. 密封面发生泄漏
B. 安全阀达不到全开状态
C. 阀瓣振荡
D. 安全阀不能迅速关闭
【多选题】
下列选项中,属于离心泵泵内损失的是___。
A. 摩擦损失
B. 水力损失
C. 机械损失
D. 容积损失
【多选题】
按阀门结构分类,阀门可以分为___。
A. 闸阀
B. 截止阀
C. 单向阀
D. 蝶阀
【多选题】
化工生产上属于定型设备的有___。
A. 吸收塔
B. 再生塔
C. 容器
D. 换热器
【多选题】
压缩机喘振的影响因素是___。
A. 压缩机的转速
B. 管网的容积
C. 压缩机进口压力
D. 压缩机功率
【多选题】
换热管及管板胀接工艺有等几种。___。
A. 机械胀接
B. 液袋胀接
C. 爆破胀接
D. 橡胶胀接
【多选题】
通过换热器型号BES700-1.27/1.61-155-6/19-4可以获得以下信息。___。
A. B指封头管箱, E指单程壳体,S指钩圈式浮头
B. 700是公称直径,mm;1.27/1.61是指管/壳程公称压力, Mpa
C. 155是指公称换热面积, m2;6/19 是指换热管长度m,及换热管外径,mm
D. 管程数为4,壳程数为1
【多选题】
化工管路保温保冷的目是___ 。
A. 减少热损和冷损
B. 增大损耗量
C. 改善劳动环境
D. 没什么作用和目的
【多选题】
废热锅炉投用后,下列___指标是锅炉水控制指标。
A. 电导率
B. pH值
C. 磷酸根
D. 钠离子
【多选题】
以下图所示,1、2、3分别指离心泵哪个部位___。
A. 轴承
B. 密封
C. 呼吸阀
D. 油视镜
【多选题】
空气冷却器的风机风量调节手段有___。
A. 调节叶片倾角
B. 风机的转速
C. 百叶窗的开启程度
D. 管束的多少
【多选题】
离心泵的主要性能是通过___ 等表示的。
A. 流量
B. 扬程
C. 功率
D. 效率
【多选题】
进汽温度过高和过低使汽轮机___。
A. 振动
B. 叶片冲刷
C. 叶片断裂
D. 零部件互相碰撞
【多选题】
转子发生工频振动的原因有___。 
A. 转子不平衡   
B. 油膜振荡   
C. 轴承无紧力
D. 对中不良
【多选题】
下列操作步骤中属于往复式压缩机有___。 
A. 润滑油系统的试车       
B. 电动机试车     
C. 压缩机无负荷试车     
D. 压缩机负荷试车
【多选题】
调节阀依气动调节阀在有信号作用时阀芯的位置可分为___两种。 
A.  、气关式    
B.  气开式 
C. 电动阀  
D.  闸阀
【多选题】
固定板式换热器有___的特点。
A. 结构简单
B. 成本低
C. 适用于壳体压力高的场所
D. 适用于壳体压力低的场所用介质
【多选题】
压力容器无损检测中射线检测对___缺陷比较有效。
A.  、裂纹    
B.  气孔 
C. 夹渣  
D. 弧坑
【多选题】
硫封罐进口液硫管线堵塞主要判断方法有___
A. 观察硫封罐溢流口液硫流动情况    
B. 检查管线伴热情况 
C. 观察系统压力是否有升高现象  
D. 观察硫冷器是否有剧烈震动现象
【多选题】
鼓风机故障的现象有___。
A.  、风量不稳定    
B.  风压不稳定 
C. 风量中断  
D. 出口压力高
【多选题】
浮头式换热器由___组成。
A. 管束
B. 浮头
C. 壳体
D. 头盖
【多选题】
阀门加油的作用是___。
A.  、保证润滑效果    
B.  有利于开关 
C. 防止泄漏  
D. 防止腐蚀
【多选题】
浮头式换热器的结构复杂,主要等零部件有___。
A.  、防冲板   
B.  挡板
C. 浮头管板  
D. 钩圈
【多选题】
U型管换热器具有___特点。
A. 弹性小
B. 热补偿性能好
C. 管程流速低
D. 承压能力高
【多选题】
活塞式压缩机的气阀,检修后进行试漏试验,不应选用___。
A.  、水   
B.  汽油
C. 煤油
D. 柴油
【多选题】
按工作原理,汽轮机可分为___两种。
A.  、凝汽式    
B.  冲动式
C. 反动式  
D. 背压式
【多选题】
与管壳式换热器相比板式换热器有哪些特点___。
A. 传热系数高    
B. 重量轻
C. 占地面积小  
D. 清洗方便
【多选题】
机械型疏水阀分类有___。
A.  、自由浮球式    
B.  自由浮球式
C. 杠杆浮球式  
D. 杠杆浮球式
【多选题】
我们装置中以下风机属于罗茨风机是___。
A.  、氧化风机    
B.  焚烧炉风机
C. 罐顶气风机  
D. 液硫池增压风机
【多选题】
以下选项属于管壳式换热器是___。
A.  、板式换热器    
B.   U型管式换热器
C. 浮头式换热器  
D. 固定管板式换热器
【多选题】
润滑“五定“是指___。
A. 定人  
B. 定质,定量
C. 定点  
D. 定时
【多选题】
废热锅炉完全烧干时补水的不正确处理方法是___
A. 可以立即补水    
B. 炉膛熄火以后就可补水
C. 等出口温度降至100℃以下再补水  
D. 等出口温度降至常温才能补水
【多选题】
环型填料有___
A.  、拉西环  
B.   鲍尔环
C. 改进鲍尔环  
D. 阶梯环
【多选题】
关于屏蔽泵说法正确的是___。
A. 输送液体不会泄漏  
B. 严禁空载运行
C. 可以允许逆向运转  
D. 电机与泵是一体
【多选题】
风机启动后无法提升压力___。
A. 电机反转  
B. 电机转速慢
C. 风机进口阀芯脱落  
D. 风机出口压力表失灵
【多选题】
液硫泵(双螺杆泵)启动注意事项有哪些___。
A. 启动时必须保证出口关闭  
B. 严禁长时间干转
C. 严禁反转  
D. 不允许依靠调节出口阀大小来满足小流量工况
【多选题】
引起法兰泄漏的原因有___。
A. 垫片选用不当
B. 法兰面破损
C. 螺栓紧力不匀
D. 介质太脏
【多选题】
换热器管束有___排列方式。
A. 等过三角形
B. 正方形
C. 正方形错列
D. 同心圆形排列
【多选题】
压力容器按其功能分为___。
A. 反应压力容器
B. 换热压力容器
C. 分离压力容器
D. 储运压力容器
推荐试题
【单选题】
Which iSCSI initiator type can be used with any network interface card?___
A. Software iSCSI initiator
B. Software FCoE adapter
C. Hardware Independent iSCSI initiator
D. Hardware Dependent iSCSI initiator
【单选题】
An administrator is attempting to power on a virtual machine with 32GB of memory. The operation fails with the following error: <Could not power on VM: No space left on device> <Checking the space on the virtual machine's datastore, there is 30GB free.> Which action would allow the VM to power on?___
A. Set a 2GB memory reservation on the VM.
B. Mount the virtual disk from the affected VM on to another virtual machine and free up space from within the OS.
C. Enable vSphere HD admission control on the cluster in which the VM resides.
D. Set a 2GB memory limit on the VM.
【单选题】
An administrator attempts to manually reclaim space on thin-provisioned VMFS6 volumes but finds that no additional space is being recovered. Which could be causing this?___
A. vSphere 6.5 does not support manual UNMAP.
B. The manual UNMAP operation has been moved to the vSphere web client.
C. The VASA version is use is incompatible.
D. UNMAP is automated for VMFS6.
【单选题】
An administrator has upgraded to vSphere 6.5 and also wants to use Kerberos authentication for NFS. Which can be done to the existing NFSv3 volumes to enable this feature?___
A. Perform a storage rescan on VMFS volumes.
B. Unmount the NFSv3 datastore, and then mount as NFSv4.1 datastore.
C. Nothing. All NFSv3 mounted datastores are upgraded automatically during vSphere upgrades.
D. Perform a scan of new storage devices.
【单选题】
An administrator wants to restore the vCenter Server Appliance 6.5 from backup. Where can this be accomplished?___
A. from the ESXi Host Client
B. from the VMware vSphere Appliance Management Interface
C. from within the VMware vSphere Web Client
D. from the vCenter Server Appliance Installer
【单选题】
The administrator wants to power on VM-K2, which has a 2GHz CPU reservation. VM-M1, VM-M2, and VM-K1 are all powered on. VM-K2 is not powered on. The exhibit shows the parent and child resource reservations. If Resource Pool RP-KID is configured with an expandable reservation, which statement is true?___
A. VM-K2 will be unable to power on because there are insufficient resources.
B. VM-K2 will be able to power on since resource pool RP-KID has 2GHz available.
C. VM-K2 will be unable to power on because only 2GHz are reserved for RP-KID.
D. VM-K2 will receive resource priority and will be able to power on this scenario.
【单选题】
Which is the block size on the VMFS6 datastore?___
A. All small and large file blocks are 8MB.
B. All small and large file blocks are 1MB.
C. Small file blocks are 512KB. large file blocks are 64MB.
D. Small file blocks are 1MB, large file blocks are 512MB.
【单选题】
When installing vCenter Converter Standalone, why must an administrator perform a client-server installation instead of a local installation?___
A. to manage conversion tasks remotely
B. to convert virtual machines as well as physical machines
C. to allow installation of the Converter agent on remote source machines
D. to hot clone physical or virtual machines
【单选题】
Which is required by vCenter Converter Standalone to convert a physical Red Hat Enterprise Linux 7 machine to a virtual machine?___
A. The Linux machine must be powered off.
B. The Linux machine must have the SSH daemon started.
C. The Linux machine must use a static IP address.
D. The Linux machine must have a fully-qualified domain name.
【单选题】
An administrator is troubleshooting network communications between a vCenter Server and an ESXi 6.5 host. Which log shows the related events between these components?___
A. /var/log/fdm.log
B. /var/log/vpxa.log
C. /var/log/hostd.log
D. /var/log/auth.log
【单选题】
An administrator has recently upgraded from vSphere 6.0 to 6.5, and can no longer see the software iSCSI named vmhba33. Which could be the reason for this?___
A. The upgrade has changed the vmhba name.
B. vSphere 6.5 automates iSCSI configurations.
C. vSphere 6.5 no longer supports software iSCSI.
D. The upgrade has deleted the vmhba.
【单选题】
An administrator is trying to vMotion a VM from his datacenter to a recovery site. Which is the maximum allowed RTT (Round-Trip Time) latency between source and destination host?___
A. 100 milliseconds
B. 150 milliseconds
C. 15 milliseconds
D. 10 milliseconds
【单选题】
Which is required for configuring iSCSI Software Adapter network port binding?___
A. VMkernel of the iSCSI traffic must be load balanced using Route based on IP Hash algorithm.
B. VMkernel of the iSCSI traffic must be load balanced using Route based on Source Virtual Port ID algorithm.
C. VMkernel of the iSCSI traffic must be load balanced using Route based on Source MAC Hash algorithm.
D. VMkernel of the iSCSI traffic must be bound to only one active network adapter.
【单选题】
In vSphere Data Protection 6.1, which is the function of a Backup Verification job?___
A. None. Backup Verification job is not a feature of vSphere Data Protection
B. It is a manual task -Power it on -Verify the guest OS -Check started applications
C. It is an automatic process -Restore a virtual machine -Power it on -Verify that the guest OS is booted by communicating with the Backup Verification agent
D. It is an automatic process -Restore a virtual machine -Power it on -Verify that the guest OC is booted by detecting the VMware ToolsTM "heartbeats"
【单选题】
An administrator has enabled vSphere Distributed Switch Health Check. The hosts connected to that Distributed Switch all display an alert:< vSphere Distributed Switch MTU supported status > .The administrator has all of the VMkernel ports MTU sizes set to 1600. Which action will remedy this problem?___
A. Configure the Distributed Switch to MTU 9100.
B. Disconnect and reconnect the physical network cable.
C. Configure the physical switch to MTU 1600.
D. Disable the Distributed Switch MTU.
【单选题】
Which Host Profile Subprofile configuration is used to configure firewall settings for ESXi hosts?___
A. Advanced Configuration Settings
B. General System Settings
C. Security
D. Networking
【单选题】
Where would a vSphere administrator find general vCenter Server logs on a vCenter Server Appliance?___
A. /var/log/vmware/vpxd/
B. /var/log/messages
C. /etc/vmware-vpx/
D. /var/log/vmware/vsan-health/
【单选题】
An administrator wishes to enable network port mirroring based on source port. Which feature should be enabled?___
A. vSphere standard switch port
B. ERSPAN
C. NSX Virtual Wire
D. VLAN
【单选题】
Which CLI command shows the physical uplink status for a vmnic?___
A. esxcli network ip connection list
B. esxcli network ip neighbor list
C. esxcli network nic get
D. esxcli network nic list
【单选题】
Which is the maximum number of block devices (LUNs) that are supported by ESXi hosts that are running version 6.5?___
A. 1024
B. 512
C. 2048
D. 256
【单选题】
When performing a vCenter Server 5.5 for Windows with Microsoft SQL Server Express database migration to vCenter Server Appliance 6.5, which will be the target database?___
A. Microsoft SQL Server Express 2012R2
B. Microsoft SQL Server Standard 2012R2
C. PostgreSQL
D. Oracle DB 11g
【单选题】
An administrator has multiple vCenter Server 6.5 systems but cannot enable Storage I/O Control (SIOC) on a datastore shared by ESXi hosts managed by the vCenter Server systems. Which action should the administrator take to resolve the issue?___
A. Unmount the datastore and then enable SIOC on the vCenter Server system.
B. Configure the datastore to be managed by a single vCenter Server system.
C. Configure Storage DRS and then enable SIOC on the vCenter Server system.
D. Enable Raw Device Mapping (RDM) on the
E. SXi hosts.
【单选题】
“OneAppServer” is a VM template stored in a content library named “LibraryOne”, but the vSphere administrator is not able to use this template for deployment. Why is the administrator unable to deploy OneAppServer?___
A. OneAppServer must be updated before it can be deployed.
B. LibraryOne is a subscribed library and OneAppServer is not downloaded yet.
C. LibraryOne is published and optimized for syncing over HTTP.
D. OneAppServer was imported from a local file on the system.
【单选题】
An administrator sets the Failover Capacity for both CPU and Memory at 25%. Based on the Exhibit below, how much of the cluster’s total CPU resources are still available to power on additional virtual machines?___
A. 45%
B. 25%
C. 70%
D. 60%
【单选题】
Which statement applies to the vSphere Replication appliance?___
A. Only one vSphere Replication appliance can be deployed per vCenter Server instance.
B. VMware Tools in the vSphere Replication appliance can be upgraded.
C. A single vSphere Replication appliance can manage a maximum of 4000 replications.
D. vSphere Replication is available only with the vSphere
E. ssentials Plus license.
【单选题】
Which esxcli namespace can a vSphere Administrator use to adjust the queue depth?___
A. esxcli system module parameters
B. esxcli storage core device
C. esxcli system module set
D. esxcli storage core adapter
【单选题】
Which statement regarding datastore clusters meets VMware’s recommended best practices?___
A. Clusters should contain only datastores presented from the same storage array.
B. Clusters should contain only datastores with equal hardware acceleration capability.
C. Clusters should contain only datastores with the same capacity.
D. Clusters should contain only datastores using the same connection method (iSCSI, FC, etc.).
【单选题】
What VM Monitoring setting would ensure that the maximum reset window for a virtual machine is 24 hours?___
A. Medium
B. Low
C. High
D. Normal
【单选题】
What is the default space threshold for vSphere Storage DRS?___
A. 80%
B. 70%
C. 90%
D. 95%
【单选题】
Which is the correct sequence to upgrade a vSphere infrastructure?___
A. vCenter Server>ESXi host> VMware Tools>VM compatibility
B. ESXi host>vCenter Server> VMware Tools>VM compatibility
C. vCenter host> ESXi host> VM compatibility> VMware Tools
D. ESXi host>vCenter Server> VM compatibility>VMware Tools
【单选题】
An administrator has a large boot from SAN cluster and wants to ensure consistent configuration by using host profiles. What special considerations are required for boot from SAN hosts?___
A. Change the “Device is shared clusterwide” setting to “false” in the host profile.
B. Verify that the boot LUN is correctly identified as the boot device in the host profile.
C. The boot from SAN device must report as a local device.
D. Host profiles are incompatible with boot from SAN hosts.
【单选题】
When using VMware Converter to import a Windows server and improve the consistency of the destination virtual machine, which optional step can be performed immediately prior to powering down the source server?___
A. Perform a final synchronization task.
B. Remove the server from the network.
C. Uninstall production applications.
D. Remove the server from the Active Directory domain.
【单选题】
Restoration of the vCenter Server Appliance is accomplished using which interface?___
A. vSphere Web Client
B. vSphere Client
C. vCenter Server Appliance Management Interface
D. vCenter Server Appliance GUI Installer
【单选题】
When attempting to migrate a virtual machine to another host in the same cluster, the error message, “Select a valid compute resource” returns. What could cause this error?___
A. Both hosts run different versions of ESXi.
B. Both hosts are not sharing the same datastore.
C. VMware Tools is not installed.
D. Virtual machine has an ISO attached.
【单选题】
When will vSphere Data Protection delete the expired backup image of a Platform Service Controller?___
A. Immediately after the retention period has expired.
B. After the expired backup image is restored.
C. During the next backup window following expiry.
D. During the next maintenance window following expiry.
【单选题】
Group A has permission to download files in Content Library. Group B does not have permission to download files in Content Library. If a user is a member of both groups, what will be the result?___
A. The user cannot download file from Content Library.
B. The user can download file from Content Library.
C. The user cannot access Content Library.
D. The user can access Content Library.
【单选题】
An administrator is trying to set up Host Partial Failure Response, but the Automated option is grayed out. What can the administrator change to enable the Automated option?___
A. Change the vSphere DRS Automation level to Partially Automated.
B. Change the vSphere DRS Automation level to Fully Automated.
C. Enable vSphere HA Host Monitoring.
D. Change the vSphere DPM Automation level to Automatic.
【单选题】
When you attempt to open a virtual machine console from the vSphere Web Client, the console does not connect. The following error message appears:<HTTP ERROR 404> <Problem accessin/.Reason: Not Found>. Why did not connect?___
A. Port 443 is in use.
B. Port 9443 is in use.
C. Port 8443 is in use.
D. Port 22443 is in use.
【单选题】
What new feature was introduced to the Content Library in vSphere 6.5?___
A. Mount an ISO directly from the Content Library.
B. Deploy a virtual machine from an OVF Package in a Content Library.
C. Upload a File from a URL to a Library Item.
D. Upload a File from a Local System to a Library Item.
【单选题】
How can an administrator exclude Encryption rights from a support engineer?___
A. Clone the role Virtual machine power user, remove Cryptographic operations privileges.
B. Clone the role Administrator and assign to the support engineer.
C. Clone the role Virtual machine power user and assign to the support engineer.
D. Clone the role No cryptography administrator and select privileges only for the support engineer.