【单选题】
中心站主机应不少于___台,1台备用。
A. 1#
B. 2#
C. 3#
D. 4
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
B
解析
暂无解析
相关试题
【单选题】
中央并列式通风的矿井,回风井大致位于___。
A. 井田浅部边界走向中央#
B. 井田中央#
C. 走向边界附近#
D. 井田边界
【单选题】
中华人民共和国___内从事煤炭生产和煤炭建设活动,必须遵守《煤矿安全规程》。
A. 领土#
B. 领海#
C. 领域#
D. 范围
【单选题】
水力冲孔的作用是___。
A. 掘进巷道#
B. 煤层注水#
C. 局部防突#
D. 降尘
【单选题】
水仓的空仓容量应经常保持在总容量的___%以上。
A. 30#
B. 50#
C. 60#
D. 70
【单选题】
水文地质条件复杂、极复杂的煤矿,应设立专门的___。
A. 防治水机构#
B. 防治水矿长#
C. 防治水设计部门#
D. 防治水
【单选题】
水采时,对使用中的水枪,每___个月应至少进行一次耐压试验。
A. 1#
B. 3#
C. 6#
D. 12
【单选题】
水泵、水管、闸阀、排水的配电设备和输电线路,必须经常检查和维护。在每年___必须全面检修1次。
A. 雨季之前#
B. 年初#
C. 年末#
D. 夏季
【单选题】
手持电气设备的操作手柄和工作中必须接触的部分必须有良好___。
A. 接地
B. 导电#
C. 绝缘#
D. 防锈
【单选题】
手持式电气设备的额定电压不得超过___V。
A. 38#
B. 36#
C. 127#
D. 24
【单选题】
从业人员经过安全教育培训,了解岗位操作规程,但未遵守而造成事故的,行为人应负___责任,有关负责人应负管理责任。
A. 领导#
B. 行政#
C. 直接#
D. 法律
【单选题】
从硐室出口防火铁门起___m内的巷道,应砌碹或用其他不燃性材料支护。硐室内必须设置足够数量的扑灭电气火灾的灭火器材。
A. 5#
B. 10#
C. 15#
D. 20
【单选题】
风门开闭状态传感器的电路组件和磁体组件间距在___mm内。
A. 10#
B. 20#
C. 30#
D. 40
【单选题】
风桥的通风断面,要求不小于原巷道断面的___,并成流线型。
A. 0.8#
B. 0.666666666666667#
C. 0.6#
D. 4/6
【单选题】
风桥的漏风率要求不大于___。
A. 0.02#
B. 0.01#
C. 0.03#
【单选题】
D、0.1 风桥最高允许风速为___m/s。
A. 7#
B. 8#
C. 9#
D. 10
【单选题】
风速传感器应当安装在巷道端面的___处。
A. 中央#
B. 底部#
C. 平均风速点#
D. 都可以
【单选题】
风速传感器离巷道顶部的距离要大于___mm。
A. 200#
B. 300#
C. 400#
D. 500
【单选题】
火灾发生在总进风流中时,应采取的控制风流措施是___。
A. 保持正常通风,稳定风流#
B. 维持原风向,减少供风量#
C. 维持原风向,增大供风量#
D. 进行矿井反风
【单选题】
计算机系统内部采用的是___数。
A. 二进制#
B. 八进制#
C. 十进制#
D. 十六进制
【单选题】
计算机要运行磁盘上的程序时,应先将文件读入到___。
A. RAM#
B. ROM#
C. 硬盘#
D. 软盘
【单选题】
心脏按压每分钟应该___次,直到复苏。
A. 30~40#
B. 50~60#
C. 72~80#
D. 90~100
【单选题】
引起瓦斯爆炸的临界温度为___。
A. 150~350℃#
B. 350~550℃#
C. 650~750℃#
D. 850~1200℃
【单选题】
以下二极管分类中属于按材料分类的是___。
A. 硅管#
B. 整流二极管
C. 发光二极管#
D. 半导体
【单选题】
以下哪种图纸不是《煤矿安全规程》规定煤矿必须填绘反映实际情况的图纸。___
A. 安全监控布置图和断电控制图#
B. 人员位置监测系统图#
C. 井田地形地质图#
D. 井下通信系统系统图
【多选题】
风速传感器应设置在巷道前后10m内___,能准确计算风量的地点。
A. 无分支风流#
B. 无拐弯#
C. 无障碍#
D. 断面无变化
【多选题】
瓦斯抽放泵站的抽放泵输入管路中宜设置___传感器。
A. 流量#
B. 温度#
C. 压力#
D. 风速
【多选题】
利用瓦斯时,应在输出管路中设置___传感器。
A. 流量#
B. 温度#
C. 压力#
D. 风速
【多选题】
防护等级IP47代表___。
A. 防护大于2.5mm的固体#
B. 防护大于1mm的固体#
C. 防浸水#
D. 防海浪
【多选题】
矿井“八害”包含___。
A. 沼气#
B. H2S#
C. H2#
D. N2
【多选题】
KJ90-F16___矿用监控分站的输入输出容量为:( AB)路模拟量或开关量的入口,( )路断电控制输出口。
A. 16#
B. 8#
C. 4#
D. 2
【多选题】
网络中心值班人员发现煤矿___情况等必须立即通知煤矿核查情况,按应急预案进行处理。
A. 瓦斯超限报警#
B. 照明无电#
C. 皮带停止运行#
D. 馈电状态异常
【多选题】
使用和维护增安型电气设备时,要注意___。
A. 设备的温度#
B. 电气间隙#
C. 爬电距离#
D. 电路和导线的连接
【多选题】
矿井地质构造的形态可以归纳为三种类型,分别为___。
A. 单斜构造#
B. 褶曲构造#
C. 断裂构造#
D. 水平构造
【多选题】
外伤急救的技术有___。
A. 止血#
B. 包扎#
C. 固定#
D. 搬运
【多选题】
周期来压的主要表现形式是:___。
A. 煤层顶板下沉速度急剧增加#
B. 煤层顶板下沉量变大#
C. 支柱所受载荷普遍增加#
D. 煤壁片帮
【多选题】
在电路中,电阻的接线形式有___。
A. 串联#
B. 焊接#
C. 并联#
D. 串并联
【多选题】
漏电保护方式主要有___。
A. 附加直流电源式#
B. 旁路接地式#
C. 零序电流方向式#
D. 闭锁式
【多选题】
隔爆型电气设备的防爆特征有___。
A. 不传爆性#
B. 气密性#
C. 本质安全性#
D. 耐爆性
【多选题】
常用的红外发光二极管,管压降约为___V,工作电流一般小于( )mA。
A. 1.0#
B. 1.4#
C. 10mA#
D. 20mA
【多选题】
场效应管的主要参数有___。
A. 饱和漏源电流#
B. 夹断电压#
C. 开关电压#
D. 漏源击穿电压
推荐试题
【单选题】
Which feature prevents loops by moving a nontrunking port into an errdisable state when a BPDU is received on that port?___
A. BPDU filte
B. DHCP snooping
C. BPDU guard
D. Port Fast
【单选题】
Which command enables port security to use sticky MAC addresses on a switch?___
A. switchport port-security violation restrict
B. switchport port-security mac-address sticky
C. switchport port-security violation protect
D. switchport port-security
【单选题】
When you edit an IPS subsignature, what is the effect on the parent signature and the family of subsignatures?___
A. The change applies to the parent signature and the entire family of subsignatures
B. The change applies to the parent signature and the subsignature that you edit
C. The change applies only to subsignatures that are numbered sequentially after the subsignature that you edit
D. Other signatures are unaffected, the change applies only to the subsignature that you dit
【单选题】
Which type of mechanism does Cisco FirePOWER de ploy to protect ag detected moving across other networks?___
A. antivirus scanning
B. policy-based
C. reputation-based
D. signature-based
【单选题】
What action must you take on the ise to blacklist a wired device?___
A. Locate the switch through which the device is connected and push an a cl restricting all access by the device
B. Issue a CoA request for the de vice's mac address to each access switch in the network
C. Revoke the device's certificate so it is unable to authenticate to the network
D. Add the device's MAc address to a list of black listed devices
【单选题】
Which type of firewall can perform deep packet inspection?___
A. packet-filtering firewall
B. stateless firewall
C. application firewall
D. personal firewall
【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
2.刀开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
3.行程开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
4.交流接触器的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
A. 频繁地
B. 偶尔
C. 手动
D. 不需
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16.短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
17.一般电气控制系统中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速