【判断题】
在吊顶内作业时,应搭设步道,非上人吊顶不得上人。
A. 对
B. 错
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【判断题】
人力移动杆段时,应动作协调,滚动前方应有人随时用木楔掩牢。
A. 对
B. 错
【判断题】
组立杆塔,吊件螺栓应全部紧固,吊点绳,承托绳、控制绳及内拉线等绑扎处受力部位,不得缺少构件。
A. 对
B. 错
【判断题】
调整临时拉线校正杆塔倾斜或弯曲时,塔上进行其他作业的人员应做好安全措施。
A. 对
B. 错
【判断题】
索道架设后应在各支架及牵引设备处安装临时接地装置。
A. 对
B. 错
【判断题】
利用索道载人,应减慢牵引速度。
A. 对
B. 错
【判断题】
用棍、杠撬拨电杆杆段时,应防止其滑脱伤人,用铁撬棍插入预埋孔转动杆段时应注意保护电杆。
A. 对
B. 错
【判断题】
钢筋混凝土电杆排杆,作业点周围5m内的易燃易爆物应清除干净。
A. 对
B. 错
【判断题】
杆塔组装,组装构件连接对孔时,严禁将手指伸入螺孔找正。
A. 对
B. 错
【判断题】
分片组装铁塔时,辅材自由端朝上时应与相连构件进行临时捆绑固定。
A. 对
B. 错
【判断题】
整体组立杆塔,指挥人员应站在能够观察到各个岗位的位置,但不得站在总牵引地锚受力的前方。
A. 对
B. 错
【判断题】
整体组立杆塔,抱杆脱帽时,杆塔应及时带上反向临时拉线,并应随电杆起立适度收紧。
A. 对
B. 错
【判断题】
带拉线的转角杆塔起立后,在安装永久拉线的同时,应在内角侧设置半永久性拉线,该拉线应在架线前及时拆除。
A. 对
B. 错
【判断题】
分解组立钢筋混凝土电杆,电杆的临时拉线数量:单杆不得少于3根,双杆不得少于4根。
A. 对
B. 错
【判断题】
分解组立钢筋混凝土电杆,抱杆的临时拉线设置不得妨碍电杆及横担的吊装。
A. 对
B. 错
【判断题】
在附着式外拉线抱杆分解组塔吊装构件过程中,吊件控制绳应随吊件的提升随时保持收紧状态。
A. 对
B. 错
【判断题】
起重机在作业中出现异常时,应在吊物稳定状态下进行检修等工作。
A. 对
B. 错
【判断题】
直升机组塔,实施作业前应明确分工,确定挂钩、脱钩等作业人员,确保参与作业人员清楚作业流程。
A. 对
B. 错
【判断题】
拆除杆塔的受力构件前应转换构件承力方式或对其进行补强。
A. 对
B. 错
【判断题】
搭设跨越架,应事先与被跨越设施的产权单位取得联系,必要时应请其派员监督检查。
A. 对
B. 错
【判断题】
使用金属格构式跨越架时,跨越架的拉线位置应根据现场地形情况和架体组立高度确定。
A. 对
B. 错
【判断题】
使用木质、毛竹或钢管材质搭设跨越架时,大横杆的间距均不得大于1.5m。
A. 对
B. 错
【判断题】
跨越架拆除施工,将跨越架整体推倒时,严禁倒向被跨越物侧。
A. 对
B. 错
【判断题】
张力放线,放线滑车允许荷载应满足放线的强度要求,安全系数不得小于2。
A. 对
B. 错
【判断题】
较大截面的导线穿入网套前,其端头应做坡面梯节处理。
A. 对
B. 错
【判断题】
牵引时接到任何岗位的停车信号均应立即停止牵引,停止牵引时应先停张力机,再停牵引机。
A. 对
B. 错
【判断题】
线路紧挂线时,当连接金具接近挂线点时应减慢牵引速度,便于作业人员在挂线点操作。
A. 对
B. 错
【判断题】
相邻杆塔同时在同相(极)位安装附件时,应制定防干扰措施并密切配合。
A. 对
B. 错
【判断题】
安装间隔棒时,安全带和后备保护绳应挂在同一根子导线上。
A. 对
B. 错
【判断题】
平衡挂线中,待割的导线应在断线点两端事先用绳索绑牢,割断后的导线抛掷时下方不得有人。
A. 对
B. 错
【判断题】
导线、地线换线施工前,应将导线、地线充分放电后方可作业。
A. 对
B. 错
【判断题】
施工现场为预防电击,接地棒应镀锌,直径应不小于12mm,插入地下的深度应大于0.4m。
A. 对
B. 错
【判断题】
同杆(塔)架设多回线路中的部分停电线路上的工作,应填用电力线路第二种工作票。
A. 对
B. 错
【判断题】
跨越施工复测跨越点断面图时,应考虑复测季节与施工季节环境温度的变化。
A. 对
B. 错
【判断题】
不停电施工时,起重工具和临时地锚应根据其重要程度将安全系数提高15%。
A. 对
B. 错
【判断题】
不停电跨越架线前对导引绳、牵引绳及承力工器具应进行逐盘(件)检查,不合格的工器具禁止使用。
A. 对
B. 错
【判断题】
跨越不停电线路时,作业人员应在跨越架内侧攀登,通过封顶架时应保证与带电体的安全距离。
A. 对
B. 错
【判断题】
不停电跨越作业,跨越架上最后通过的导线、地线、引绳或封网绳等,应留有绝缘绳做控制尾绳,防止滑落至带电体上。
A. 对
B. 错
【判断题】
不停电跨越作业,跨越档两端铁塔的附件安装应进行二道防护,即采用包胶钢丝绳将导线圈住并挂于横担上。
A. 对
B. 错
【判断题】
停电跨越作业,验明线路确无电压后,作业人员应按照工作票上接地线布置的要求,立即挂工作接地线。
A. 对
B. 错
【判断题】
停电跨越作业,在绝缘架空地线上作业时,应先将该架空地线接地。
A. 对
B. 错
推荐试题
【单选题】
Which feature prevents loops by moving a nontrunking port into an errdisable state when a BPDU is received on that port?___
A. BPDU filte
B. DHCP snooping
C. BPDU guard
D. Port Fast
【单选题】
Which command enables port security to use sticky MAC addresses on a switch?___
A. switchport port-security violation restrict
B. switchport port-security mac-address sticky
C. switchport port-security violation protect
D. switchport port-security
【单选题】
When you edit an IPS subsignature, what is the effect on the parent signature and the family of subsignatures?___
A. The change applies to the parent signature and the entire family of subsignatures
B. The change applies to the parent signature and the subsignature that you edit
C. The change applies only to subsignatures that are numbered sequentially after the subsignature that you edit
D. Other signatures are unaffected, the change applies only to the subsignature that you dit
【单选题】
Which type of mechanism does Cisco FirePOWER de ploy to protect ag detected moving across other networks?___
A. antivirus scanning
B. policy-based
C. reputation-based
D. signature-based
【单选题】
What action must you take on the ise to blacklist a wired device?___
A. Locate the switch through which the device is connected and push an a cl restricting all access by the device
B. Issue a CoA request for the de vice's mac address to each access switch in the network
C. Revoke the device's certificate so it is unable to authenticate to the network
D. Add the device's MAc address to a list of black listed devices
【单选题】
Which type of firewall can perform deep packet inspection?___
A. packet-filtering firewall
B. stateless firewall
C. application firewall
D. personal firewall
【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
2.刀开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
3.行程开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
4.交流接触器的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
A. 频繁地
B. 偶尔
C. 手动
D. 不需
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16.短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
17.一般电气控制系统中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速