【多选题】
对不合格品可以采取纠正的方式进行处置，下列_______不属于纠正___
A. 返工
B. 让步
C. 降级
D. 返修
查看试卷，进入试卷练习
微信扫一扫，开始刷题
答案
BCD
解析
暂无解析
相关试题
【多选题】
产品责任用于描述生产者或他方对因产品造成的与人员伤害，财产损坏或其它损害有关的损失赔偿责任的通用术语。___
A. 产品责任贯彻责任倒置原则
B. 存档文件和资料必须采用碳素墨水笔或黑色签字笔记录
C. 每12个月至少审核一次
D. 相关文件、资料和记录至少保存15年
【多选题】
防错验证的目的___
A. 确保防错/错误探测装置正常工作
B. 防止制造中传递不合格品
C. 为每台防错装置建立历史档案以指示何时需要对其进行预防性维护或维修
D. 在整个过程中对使用防错装置过程中培养良好的行为规范
【多选题】
在批量生产阶段，企业可以采用 等方法对供应商进行质量控制。___
A. 监控供应商的过程能力指数和过程性能指数
B. 监控供应商的测量系统
C. 评价供应商生产能力
D. 进货质量检验
【多选题】
在Xbar-R图中，_______被判定为异常情况___
A. 1界外----点子出界
B. 7单侧---连续7点落在中心线同一侧
C. 6连串---连续6点递增或递减
D. 12交替---连续12点相邻点上下交替
【多选题】
以下关于“纠正”和“纠正措施”的理解正确的是___
A. 纠正措施是为消除已发现的不合格或其它不期望情况的原因所采取的措施
B. 纠正是为消除已发现的不合格所采取的措施
C. 纠正是为消除已发生的不合格并就其产生的原因所采取的措施
D. 纠正和纠正措施是有区别的
【多选题】
以下关于预防措施的理解正确的是:___
A. 为消除潜在不合格或其它潜在不期望情况的原因所采取的措施
B. 采取预防措施是为了防止再发生
C. 采取预防措施是为了防止发生
D. 预防措施和纠正措施没有区别
【多选题】
关于“内部审核”，下列说法正确的是___
A. 内部审核是组织自我评价、促进自我改进的一个重要手段
B. 内部审核程序应该形成文件
C. 内部审核程序应包括审核的策划、实施、结果报告和记录
D. 组织可随意实施内部审核
【多选题】
PPAP是指生产零件的批准程序，下列何状态变化需要向主机厂用户重新提交并认可___
A. 产品设计发生变化
B. 加工工艺发生变化
C. 生产场地发生变化
D. 分供方发生变化
【多选题】
PPAP过程流程图中顾客的要求主要包括 ，供方需要向顾客提交的PPAP批准中得到体现。___
A. 顾客的采购订单/特殊要求
B. 顾客零件设计要求
C. 顾客过程设计要求
D. 顾客的规范和顾客物流要求
【多选题】
关于生产件样品与标准样件的说法正确的是___
A. 生产件样品和标准样件均是在PPAP有效的生产条件下生产的
B. 标准样件取自于生产件样品
C. 标准样件是从全尺寸检测件中抽取的一件样件
D. 标准样件与生产件样品是同一件，只是说法不一而已
【多选题】
对于标准样件的要求有___
A. 与生产件批准的记录保存相同的时间
B. 在标准样品上必须作出标识，标出顾客批准的日期
C. 必须得到顾客书面批准，才能改变或放弃对标准样品的保留要求
D. 直到生产出一个用于顾客批准，而且是相同顾客零件编号的新的标准样件为止
【多选题】
标准样件的作用是___
A. 帮助确定生产标准
B. 特别用于数据含糊的情况，或缺乏充分的细节来完全再现初始批准状态下的零件时
C. 在设计记录、控制计划或检验准则要求的地方，存放标准样件，作为参考或标准
D. 以上均不是
【多选题】
PPAP担保书中零件的重量（质量）的理解是___
A. 要发运的零件重量
B. 除非另有规定，否则以千克为单位，小数点后保留4位
C. ,零件重量不包括运输时的保护装置、包装材料和装配辅具
D. 随机选取10件的平均值重量
【多选题】
对顾客的PPAP批准状态的理解正确的是___
A. 批准、临时批准和拒收三种状态
B. 批准、拒绝二种状态
C. 临时批准是在有限时间、有限数量内交付生产需要的零件，要达到批准状态，需要再次提交PPAP
D. ，拒收是不符合顾客要求，零件不能交运。必须得到纠正，得到顾客的批准
【多选题】
关于控制计划的理解正确的是___
A. 零件和过程控制系统的书面描述，不同的控制计划覆盖三个不同的阶段
B. 样件：在样件制造过程中，对尺寸测量，材料和性能测试的描述
C. 试生产：在样件之后，批量生产之前，对尺寸测量，材料和性能测试的描述
D. 大量生产过程中，对产品/过程特性，过程控制，测试，测量系统的综合描述
【多选题】
APQP策划与定义阶段产品可靠性研究是考虑___
A. 指定时间段内部件的修理和更换频次
B. 长期可靠性/耐久性的测试结果
C. 可靠性的衡量指标和目标
D. 只是可靠性研究，没有实质意义
【多选题】
FMEA中识别和评估风险，正确的说法是___
A. 评估包括严重度、发生频度、探测度三个方面
B. 严重度是评估失效对顾客的影响等级
C. 发生频度是指一个失效模式可能的发生频率
D. 探测度是评估产品和过程控制对失效原因或失效模式的探测能力
【多选题】
FMEA中识别和评估风险，正确的说法是___
A. 评估包括严重度、发生频度、探测度三个方面
B. 严重度是评估失效对顾客的影响等级
C. 发生频度是指一个失效原因可能的发生频率
D. 探测度是评估产品和过程控制对失效原因或失效模式的探测能力
【多选题】
关于FMEA中建议措施，正确的说法是___
A. 目的在于降低整体风险和失效模式发生的可能性
B. 目的是降低严重度、发生频率、探测度
C. 需要记录完成建议措施的时间和职责人员
D. 一旦完成措施，获得结果，需要重新评估并记录严重度、发生频率和探测度的等级
推荐试题
【单选题】
During an upgrade, the ESXi 6.x installer finds an existing version of ESXi and a VMFS3 volume. No virtual machines exist on the host or VMFS3 volume. The requirement is to upgrade to VMFS5. Which option should be chosen to meet this requirement?___
A. Upgrade ESXi and preserve the VMFS datastore
B. Install ESXi and preserve the VMFS datastore
C. Install ESXi and overwrite the VMFS datastore
D. Upgrade
E. SXi and overwrite the VMFS datastore
【单选题】
A vSphere 6.x Standard Switch is configured with 4 virtual machine portgroups, as shown in the exhibit. Which portgroup would be utilized by default when creating a new virtual machine?___
A. Access Network
B. DMZ Network
C. VM Network
D. Virtual Machine Network
【单选题】
Which vSphere 6.x feature will allow an organization to utilize native snapshots?___
A. Virtual Volumes
B. Virtual SAN
C. VMFS3
D. VMFS5
【单选题】
An administrator is creating a new vSphere Distributed Switch that will be utilized with a specific vSphere Cluster. The cluster itself contains a mix of ESXi 5.x and 6.x Hosts. Which Distributed Switch version should be created to support this configuration?___
A. Distributed Switch: 6.0.0
B. Distributed Switch: 5.0.0
C. Distributed Switch: 5.1.0
D. Distributed Switch: 5.5.0
【单选题】
Which load balancing policy, previously limited to vSphere Distributed Switches, is now available on vSphere Standard Switches with vSphere 6.x?___
A. Route based on physical NIC workload
B. Route based on IP Hash
C. Route based on the originating virtual port
D. Route based on Source MAC Hash
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.
【单选题】
An administrator has an application that requires connection directly to PCI devices through a virtual machine. What is a limitation of this configuration? ___
A. Devices must be reserved for PCI passthrough on at least one host on which the virtual machine will run.
B. Snapshots are not supported with DirectPath I/O passthrough devices.
C. A maximum of 18 PCI vSphere
D. irectPath devices can be added to a virtual machine.
【单选题】
The vSphere administrator is configuring directory services for an ESXi host: What should the vSphere administrator do to configure the host to use CAM services? ___
A. Check the Use vSphere Authentication Proxy checkbox.
B. Set Select Directory Service Type to CAM services.
C. Specify CAM$ for the
D. omain.
【单选题】
Which statement is true regarding the licensing of vCenter Server? ___
A. The license for vCenter Server must be provided at the time of installation.
B. Changing the license assigned to vCenter Server requires a restart of the vCenter Server service.
C. Virtual machines can still be powered on if the vCenter Server license expires.
D. Licensing for a single vCenter Server installation is determined by the number of managed virtual machines.
【单选题】
When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected? ___
A. 1 min
B. 5 min
C. 10 min
D. 15min
【单选题】
A developer needs to create a multi-tier development stack for a home lab. Which vSphere product will support the architecture required for the least software cost? ___
A. vSphere Hypervisor
B. vSphere Essentials
C. VMware Player
D. VMware Workstation
【单选题】
An administrator is installing Windows into a virtual machine. The DVD has been mounted on the Host and configured for the virtual machine as shown in the Exhibit. Based on the exhibit, when the virtual machine is booted, why would it attempt to search for a PXE server? ___
A. The CD/DVD device is not connected.
B. The ISO is in the incorrect storage location.
C. The OS minimum requirements have not been met.
D. The CD/DVD device is not set to Client Device.
【单选题】
What component must be installed prior to deploying a vCenter Server in vSphere 6.x? ___
A. vCenter Identity Services
B. Platform Services Controller
C. vCenter Single Sign-On
D. Client Integration Plug-In
【单选题】
What is a valid plug-in status for a plug-in that has been added to a vSphere client? ___
A. Disabled
B. Unknown
C. Stopped
D. Installed
【单选题】
Users of an application are reporting performance issues. The following performance values are observed in the vSphere Web Client: <Host CPU utilization is 90%> <Virtual Machine memory utilization is consistently greater than 90% CPU Ready values are higher than 20%> What could be the cause of the application performance issue? ___
A. The host is lacking the CPU resources required to meet the demand.
B. The host is lacking the memory resources required to meet the demand.
C. The virtual machine is lacking the CPU resources required to meet the demand.
D. The virtual machine is lacking the memory resources required to meet the demand.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is re-provisioning an ESXi host and moving it to another datacenter. Which DCUI option should the administrator use to revert the system configuration to the default settings? ___
A. Reset System Configuration
B. Rebuild Default System Configuration
C. Revert System Configuration
D. Renew Default System Configuration
【单选题】
An administrator has just completed installing an ESXi 6.x host, but doesn't know what address has been configured. Where is the ESXi host IP address configured? ___
A. RVC console
B. Direct Console User Interface
C. vSphere Web Client
D. vSphere Client
【单选题】
When is it possible to place a VMFS5 datastore in maintenance mode? ___
A. When it is a member of a Storage DRS cluster
B. When it is a member of Virtual SAN cluster
C. When it is a member of a multi-extent datastore
D. When it is a member of a Virtual Volume
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
