【多选题】
在测量电气设备绝缘电阻时，影响绝缘电阻的因素主要有。___
A. 被测设备环境温度相对增大时，绝缘电阻降低
B. 被测设备表面脏污会使其绝缘电阻显著下降
C. 被测设备停电后，放电的残余电荷或试验后放电的残余电荷，造成试验或再次试验的绝缘偏大或偏小
D. 电容耦合，带电设备将使被测的设备带上一定的感应电压，将影响其绝缘电阻测量值
查看试卷，进入试卷练习
微信扫一扫，开始刷题
答案
ABCD
解析
暂无解析
相关试题
【多选题】
为防止电缆试验过程中发生触电伤害，在变更接线时下列哪些做法是正确的。___
A. 必须断开试验电源
B. 被试电缆逐相多次放电
C. 将升压设备的高压部分短路
D. 将升压设备的高压部分接地
【多选题】
剩余电流动作保护器安装后应进行的试验有。___
A. 试验按钮试验3次，均应正确动作
B. 带负荷分合交流接触器或开关3次，不应误动作
C. 每相分别用3kΩ试验电阻接地试跳，应可靠动作
D. 每相分别用5kΩ试验电阻接地试跳，应可靠动作
【多选题】
使用吊车位移正杆的正确步骤是。___
A. 用吊车将杆子固定，吊点绳位置一般在距杆跟2-3m处
B. 摘除杆上固定的导线，使其脱离杆塔，然后登杆人员下杆
C. 在需要位移一侧靠杆根处垂直挖下，直到杆子埋深的深度
D. 使用吊车将杆子移到正确位置，校正垂直，然后将杆根土方回填夯实，恢复并固定导线，位移工作即告结束
【多选题】
配电线路单横担安装的要求。___
A. 直线杆横担应装于受电侧
B. 分支杆、90°转角杆及终端杆横担应装于拉线侧
C. 横担安装应平整，横担端部上下歪斜和左右扭斜不应大于20mm
D. 直线杆横担应装与供电侧
【多选题】
进行电能表安装时的要求有。___
A. 电能表必须牢固地安装在可靠及干燥的墙板上，其周围环境应干净、明亮，便于装拆、维修
B. 电能表安装的场所必须是干燥、无震动、无腐蚀性气体
C. 电能表的进线、出线，应使用铜芯绝缘线，芯线截面要根据负荷而定，但不得小于1.5mm2，中间不应有接头，接线要牢，裸露的线头部分不可露出接线盒，自总熔断器盒至电能表之间敷设的导线长度不宜超过20m，在进入电能表时，一般以“左进右出”原则接线
D. 电能表接线必须正确，如果电能表是经过电流互感器接入电路中，电能表和互感器要尽量靠近些，还要特别注意极性和相序
【多选题】
造成电动机缺相运行的原因有，以及触点、接线端接触不良或因氧化锈蚀而接触电阻过大。___
A. 电源电压缺相
B. 电动机主电路熔断器熔断一相
C. 电动机定子绕组一相断线
D. 开关和起动控制设备等接线不良
【多选题】
负载与电源连接的原则：一是保证负载得到额定电压，二是尽量使三相负载对称分布。无论是三相交流电源还是三相负载都有星形(Y)和三角形(△)两种连接方式。因此，三相电路可能实现的连接方式共有种连接。___
A. Y-Y
B. Y-△
C. △-Y
D. △-△
【多选题】
使用手提式干粉灭火器时，先打开喷嘴盖，拔出保险销，提起灭火器，然后一只手握住喷粉管，把喷嘴对准火焰根部，一只手按下压把，，注意不要使火焰窜回，以防复燃。___
A. 由远到近
B. 由近到远
C. 左右横扫
D. 迅速推进
【多选题】
对于高压用户，供电企业审核的用户受电工程设计文件和有关资料一般包括。___
A. 受电工程设计及说明书
B. 自备电源及接线方式
C. 用电功率因数计算及无功补偿方式
D. 负荷组成、性质及保安负荷
【多选题】
扑救旋转电机的火灾时，应注意。___
A. 先断开电源
B. 扑救旋转电机的火灾时，为防止轴承变形，可使用喷雾水流均匀冷却，不得用大水流直接冲射
C. 另外可用二氧化碳、1211、干粉灭火器扑救
D. 严禁用黄砂扑救，以防进入设备内部损坏机芯
【多选题】
脚扣登杆的注意事项有。___
A. 使用前必须仔细检查脚扣各部分:有无断裂、腐朽现象，脚扣皮带是否结实，牢固，如有损坏，应及时更换，不得用绳子或电线代替
B. 一定要按电杆的规格，选择大小合适的脚扣，使之牢靠地扣住电杆
C. 穿脚扣时，脚扣带的松紧要适当，应防止脚扣在脚上转动或脱落且上、下杆的每一步都必须使脚扣与电杆之间完全扣牢，以防下滑及其它事故
D. 在登杆前，应对脚扣作人体载荷冲击试验，检查脚扣是否牢固
【多选题】
防止照明器具引发火灾的主要措施有。___
A. 让灯泡远离易燃物
B. 在易燃物场所必须使用防爆灯
C. 经常检查绝缘和清洁状况，防止短路起火
D. 在易燃物场所必须使用普通灯具
【多选题】
关于正序、负序和零序概念正确的有。___
A. 三相正弦量中A相比B相超前120°，B相比C相超前120°，C相比A相超前120°，即相序为A-B-C，这样的相序叫正序
B. 三相正弦量中A相比B相滞后120°，B相比C相滞后120°，C相比A相滞后120°，即相序为A-C-B，这样的相序叫负序
C. 三相正弦量A相比B相超前0°，B相比C相超前0°，C相比A相超前0°，即三者同相，这样的相序叫做零序
D. 三相正弦量中A相比B相超前90°，B相比C相超前90°，C相比A相超前90°，即三者同相，这样的相序叫做零序
【多选题】
《国家电网公司电费抄核收管理规则》规定，对用的客户，应根据电费收缴风险程度，实行每月多次抄表，并按国家有关规定或合同约定实行预收或分次结算电费。___
A. 用电量较大的客户
B. 临时用电客户
C. 租赁经营客户
D. 交纳电费信用等级较差
【多选题】
在配电系统中三相负荷和单相负荷连接的原则是。___
A. 三相负荷的连接方式，分为星形和三角形两种，当负载的额定电压等于电源的相电压时，负荷应接成星形
B. 当额定电压等于电源的线电压时，应接成三角形
C. 对于单相负荷也是根据它的额定电压应等于电源电压的原则确定应接入相电压还是线电压
D. 单相负荷应尽量均匀地分配在三相上，使三相电源上分配的负荷尽量平衡
【多选题】
自发电用户应注意的安全措施有。___
A. 自发电机组的中性点(TT、TN系统)要单独接地，接地电阻不大于4Ω，禁止利用供电部门线路上的接地装置接地
B. 自发电用户的线路严禁借用供电部门的线路杆塔，不准与供电部门的电杆同杆架设，不准与供电部门的线路交叉跨越，不准与公用电网合用接地装置和中性线
C. 与公用电网连接的地方小水电、小火电、小热电，除采取上述安全措施外，还必须执行其他有关的规定
D. 自发电用户，严禁擅自向其他用户转供电
【多选题】
吊装配电变压器的安全注意事项有。___
A. 吊放变压器之前，应对钢丝绳套进行外观检查，无断股、烧伤、挤压伤等明显缺陷，满足起重设备荷重要求
B. 吊放前，应对各个受力点进行检查，检查变压器是否已挂好
C. 检查变压器吊环有无裂纹
D. 吊放变压器及吊车转位时，吊臂下严禁有人逗留
【多选题】
导线连接的基本要求有。___
A. 接触紧密，接头电阻不应大于同长度、同截面导线的电阻
B. 接头的机械强度不应小于该导线机械强度的80%
C. 接头处应耐腐蚀，防止受外界气体的侵蚀
D. 接头处的绝缘强度与该导线的绝缘强度应相同
推荐试题
【多选题】
Which two storage controller configurations can be used with Virtual SAN? (Choose two.)___
A. SAS controllers in Passthrough mode
B. SAS controllers in RAID0 mode
C. SAS controllers in RAID1 mode
D. SAS controllers in RAID10 mode
【多选题】
Which three are requirements when using vMotion to move a virtual machine across vCenter Server systems? (Choose three.)___
A. Both vCenter Servers must be using Enhanced Linked Mode.
B. Both vCenter Servers must be in the same Single Sign-On Domain.
C. Time must be synchronized.
D. Duplicate VM MAC addresses must be configured.
E. Both vCenter Servers must have High Availability enabled on source and destination clusters.
【多选题】
Which two components can be used when configuring Enhanced Linked Mode? (Choose two.)___
A. vCenter Server Appliance
B. vRealize Operations Manager
C. vSphere Management Appliance
D. vCenter Server for Windows
【多选题】
An organization has a number of virtual machines that would benefit from Fault Tolerance. These include: <A single vCPU Apache Server> < A dual vCPU vCenter Server> < A quad vCPU SQL Server> <An eight vCPU Hadoop Server>. Which two virtual machines can be configured to use VMware Fault Tolerance? (Choose two.)___
A. Apache Server
B. vCenter Server
C. SQL Server
D. Hadoop Server
【多选题】
Which two badges are major badges in vRealize Operations? (Choose two.)___
A. Risk
B. Efficency
C. Workload
D. Faults
【多选题】
An administrator is deploying multiple Windows 2003 Virtual Machines from the same template. What two steps should be taken to avoid network conflicts? (Choose two.)___
A. Customize the guest operating system.
B. Install VMware Tools into the new virtual machines.
C. Copy the Microsoft Sysprep tools onto the vCenter Server system.
D. Ensure the e1000 vmnic is selected for each new virtual machine.
【多选题】
Which three conditions would prevent Storage I/O Control from being enabled on a group of datastores? (Choose three.)___
A. The datastores planned for the solution are used by different vSphere clusters.
B. A datastore planned for the solution is configured as a Raw Device Mapping file.
C. A datastore planned for the solution has three extents.
D. A datastore planned for the solution is configured as NFS.
E. The organization has an Enterprise license.
【多选题】
Which two actions are prerequisites to adding ESXi 6.x hosts to a vSphere Distributed Switch? (Choose two.)___
A. Verify that there is at least one Distributed Port Group on the Distributed Switch.
B. Verify that the Distributed Port Group have active uplinks configured in its teaming and failover policy.
C. Verify that the
D. istributed Switch has been configured with a Network Profile.
【多选题】
An organization has configured Distributed Power Management (DPM) on a vSphere 6 cluster. The organization wants to be alerted when an ESXi host has been powered down by DPM. Which two options represent the type and name of the alarm that would accomplish this? (Choose two.)___
A. DrsEnteringStandbyModeEvent
B. DrsEnteredStandbyModeEvent
C. Event-based
D. Condition-based
【多选题】
Which two allow for the disabling of Network Rollback operations? (Choose two.)___
A. Modifying the vpxd advanded configuration options and adding the config.vpxd.network.rollback key
B. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\vpxd.cfg file and adjusting the<rollback> xml tag
C. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\vpxd.cfg file and adjusting the <networkrollback> xml tag
D. Modifying the C:\ProgramData\VMware\CIS\cfg\vmware-vpx\firstboot\vpxd-service- spec.prop file and adjusting the <rollback> xml tag
【多选题】
An administrator is tasked with performing a vMotion migration of a virtual machine. The virtual machine is configured as follows: <vSphere Flash Read Cache (vFRC) enabled> <Is part of a Distributed Resource Cluster (DRS) Cluster> Which two statements are true? (Choose two.)___
A. Each ESXi host in the cluster supports multiple virtual flash resources.
B. Each ESXi host in the cluster supports one virtual flash resource.
C. DRS treats powered-on virtual machines with Flash Read Cache as having a preferred affinity to their current host and moves them only for mandatory reasons.
D. DRS treats powered-on virtual machines with Flash Read Cache as having a required affinity to their current host and does not move them.
【多选题】
An administrator is using the Host Failures to Tolerate Admission Control Policy for a vSphere High Availability ___ cluster. When configuring this setting on the cluster, the administrator sees this error message: <Insufficient resources to satisfy HA failover level on cluster > What are two likely causes for the error? (Choose two.)(AB)
A. The hosts in the cluster are disconnected.
B. A host in the cluster is displaying an HA error.
C.
D. istributed Resource Scheduler has not been configured on the cluster.
【多选题】
What are two ways to identify TCP/IP stack information? (Choose two.)___
A. Using the vSphere Web Client
B. Using esxcli network ip netstack
C. Using esxcfg-netstack
D. Using the vSphere Client
【多选题】
Which two actions are required when enabling vFlash Read Cache for a virtual machine's virtual disk? (Choose two.)___
A. A value in the Virtual Flash Read Cache text box must be entered.
B. A Flash Resource Pool for Cache size reservation must be entered.
C. The Device backing and the block size must be configured.
D. The
E. nable virtual flash host swap cache check box must be selected.
【多选题】
What two IT infrastructure components are virtualized by vSphere Essentials? (Choose two.)___
A. Networks
B. Applications
C. Storage
D. Management
【多选题】
When attempting to access a virtual machine, an administrator is unable to login using the vSphere credentials. What two options are probable causes of the authentication failure? (Choose two.)___
A. The vSphere credentials have not been granted permissions.
B. The vSphere credentials are granted read-only permissions.
C. The vSphere credentials are granted no-access permissions.
D. The vSphere credentials are not a member of the local administrator group.
【多选题】
An administrator is performing a scripted installation of ESXi 6.x. In which three locations does the script need to be? (Choose three.)___
A. PXE Server
B. HTTPS
C. FTP
D. NFS
E. VVOLs Datastore
【多选题】
In order for a company to meet regulatory requirements, all ESXi 6.x Hosts must be configured to direct logs to a syslog server. What are two ways ESXi hosts can configured for this action? (Choose two)___
A. Use the esxcli system syslog command.
B. Edit them in the ESXi host Advanced System Settings.
C. From the Syslog collector user interface of the Web Client.
D. Syslog logging is not available for
E. SXi Hosts.
【多选题】
Which three actions can be executed when an alarm is triggered? (Choose three.)___
A. Send an email.
B. Send an SNMP trap.
C. Run a script or command.
D. Run an Orchestrator workflow.
E. Send a trigger to syslog.
【多选题】
An administrator is attempting to power on a virtual machine, but is unable to do so. Which two reasons are probable causes of the failure? (Choose two.)___
A. Storage access to the virtual machine swap file has been lost.
B. One of the virtual machine VMDK files is locked.
C. Virtual machine is running CentOS 7.0 64-bit.
D. Virtual machine has Hyper-Threading enabled.
【多选题】
An administrator has configured a host profile so that ESXi 6.x hosts will point to the corporate NTP server for time synchronization. The NTP server is located at 10.0.30.213, but time has not been synchronized properly across the ESXi hosts. The administrator reviews Host Profile settings as shown in the Exhibit. Which two steps are required to resolve the issue? (Choose two.)___
A. Correct the NTP server IP address.
B. Check the host for host profile compliance.
C. Remediate the host based on the updated host profile.
D. Change the NTP server to the FQDN as IP Addresses are not supported.
【多选题】
An administrator is attempting to migrate a large Hadoop virtual machine using vMotion. The administrator notices a delay when the machine is quiesced. The Hadoop virtual machine is processing many transactions a second to an in-memory database. Which two actions would help reduce the amount of time needed to perform a vMotion on this virtual machine? (Choose two.)___
A. Use multiple NICs for the vMotion vmkernel port.
B. Use a 10Gbps Network card for the vMotion vmkernel port.
C. Add an additional management network to help transmit the data quicker.
D. Disable Fault Tolerance before performing the vMotion.
【多选题】
An administrator is installing a new network card in an ESXi 6.x host that is part of a vSphere cluster. When the host is placed into maintenance mode, the vSphere Web Client displays the progress bar at 2% for over 30 minutes. Which two are likely reasons for this occurrence? (Choose two.)___
A. Maintenance mode is unable to migrate all virtual machines from the host.
B. There is a large number of virtual machines that must be migrated from the host.
C. VMware High Availability is in the process of reconfiguring the cluster.
D. Each virtual machine on the
E. SXi host must be reconfigured to recognize the new adapter.
【多选题】
Which two events happen when Distributed Resource Scheduler (DRS) is disabled? (Choose two.)___
A. The cluster's resource pool heirarchy and affinity rules are re-established when DRS is turned back on.
B. The cluster's resource pool hierarchy and affinity rules are not re-established when DRS is turned back on.
C. The cluster's resource pools are removed from the cluster.
D. The cluster's resource pools are removed from the cluster and assigned to the hosts.
【多选题】
Which two networking connection types can be configured on a virtual switch? (Choose two.)___
A. Virtual machine portgroups
B. VMkernel services (such as NFS, iSCSI, or vMotion) to the physical network
C. Web services over the Management Network
D. NFS and FCoE storage services
【多选题】
An administrator creates a DRS cluster of eight ESXi 6.x hosts. There are 10 virtual machines balanced across the hosts. An attempt to place the first host into maintenance mode fails. What are two reasons that the host failed to enter maintenance mode? (Choose two.)___
A. The DRS cluster Automation Level is set to Partially Automated mode.
B. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Should run on hosts in group.
C. One of the virtual machines on the ESXi Host entering maintenance mode is configured with a DRS Host affinity rule Must run on hosts in group.
D. One of the virtual machines on the
E. SXi Host entering maintenance mode is configured with an individual Automation Level set to Partially Automated.
【多选题】
When modifying a vApp, which two vSphere entities can be added? (Choose two.)___
A. A resource pool
B. A network pool
C. A vApp
D. A folder
【多选题】
From which two locations in the inventory hierarchy can you deploy a virtual machine using a template? (Choose two.)___
A. Directly from the template.
B. From a compute resource.
C. From an existing virtual machine.
D. From a Datastore.
【多选题】
A company has decided to implement Virtual SAN within their vSphere 6.x environment. The Virtual SAN cluster will be composed of three ESXi 6.x hosts that are on the Virtual SAN Ready Node list. Each ESXi host includes: <Two SAS Controllers that support Passthrough Mode> < Four Solid State Drives (SSDs) 1TB in size each> <20 SAS Magnetic Disks (MDs) 1TB in size each> <The SSDs and MDs are evenly split between the two SAS controllers>. The company will pilot a Virtual SAN cluster utilizing VMware best practices while maximizing storage capacity. The Virtual SAN cluster will use Manual Mode. Which two Disk Group configurations would meet the stated configuration requirements? (Choose two.)___
A. 4 disk groups with 1 SSD and 5 MDs each
B. 2 disk groups with 1 SSD and 7 MDs each
C. 2 disk groups with 2 SSDs and 7 MDs each
D. 2 disk groups with 1 SSD and 10 MDs each
【多选题】
A physical Windows 2008 R2 Server is converted to a virtual machine using VMware vCenter Converter. Upon completion of the conversion and subsequent power on operation, the virtual machine fails to boot and the message below is observed in the Console of the virtual machine: <STOP 0x0000007B INACCESSIBLE_BOOT_DEVICE>. Which two potential issues may be causing this boot failure? (Choose two.)___
A. An incorrect SCSI controller was selected during conversion.
B. Incompatible software drivers were migrated into the virtual machine from the source machine.
C. The vmdk file backing the virtual machine was thick provisioned.
D. A snapshot was taken immediately after the conversion completed.
【多选题】
An administrator is configuring the Failover Order option on a vSphere Distributed Switch. Which two options should be used with IP-hash load balancing? (Choose two.)___
A. Active Uplinks
B. Standby Uplinks
C. Unused Uplinks
D. Override Failover Order
【多选题】
An administrator is configuring the Maximum Transmission Unit value on a vSphere Distributed Switch. Which two options are typical values for ESXi networking? (Choose two.)___
A. 1492
B. 1500
C. 9000
D. 9089
【多选题】
Which two configurable options apply to both virtual machine CPU and memory allocation? (Choose two.)___
A. Reservation
B. Shares
C. Resource Pool
D. Reserve All
【多选题】
When attempting to power on a Virtual Machine you observe the following error: <Cannot open the disk '/vmfs/volumes/volume/vm/vm-000002.vmdk' or one of the snapshot disks it depends on.> Which three actions will be the best solutions to address this problem? (Choose three.)___
A. Verify that the virtual machine's disk files are present.
B. Investigate the host and virtual machine log files.
C. Verify the vmdk descriptor files and if required, recreate them.
D. Delete the disk file preventing the power on operation.
E. Migrate or register the virtual machine to a different host.
【多选题】
An administrator has been tasked with enabling High Availability ___ on a cluster in a vSphere 6.x environment with default settings. The cluster configures properly and there are no errors. The next day when powering on a virtual machine, an error is presented: <Not Enough Failover Resources>. Which three scenarios are likely causes of this error message? (Choose three.)(CDE)
A. The default VM Monitoring Sensitivity is set too high.
B. There are not enough datastore heartbeat datastores configured by default.
C. The default slot size in the cluster is set too high.
D. There are virtual machines with large CPU reservations.
E. A host is in maintenance mode for a replacement of a failed Hard Drive.
【多选题】
vMotion can be performed between which three physical boundaries? (Choose three.)___
A. Between two vCenter Server Systems
B. Between two vSphere Distributed Virtual Switches
C. Between two vCenter Server Datacenter objects
D. Between two VMware NSX Layer 4 segments
E. Between two NFS datastores
【多选题】
An administrator configures vSphere Replication for a virtual machine and enables multiple point in time (PIT) instances under the recovery settings in the Configure Replication wizard. Which two statements are correct for vSphere Replication with multiple point in time instances enabled? (Choose two.)___
A. vSphere Replication retains a number of snapshot instances of the virtual machine on the target site based on the retention policy that you specify.
B. vSphere Replication uses the virtual machine's snapshot instances to define the target site Point in Time instance based on the retention policy that you specify.
C. vSphere Replication does not support virtual machines with snapshots.
D. vSphere Replication supports virtual machines with snapshots.
【多选题】
An administrator is virtualizing a physical application server and adding it to an existing multi-tiered vApp. The application license is currently tied to the physical NIC's MAC address, so the administrator needs to ensure the license will function properly in the virtual machine. Which two actions can the administrator take to satisfy this task? (Choose two.)___
A. Set the MAC address for the vNIC in the guest operating system.
B. Install the physical server's NIC into the ESXi host.
C. Configure the MAC address for the vNIC using the vSphere Web Client.
D. Assign the physical server NIC's MAC address in the vSphere Distributed Switch.
【多选题】
Which two Fibre Channel zoning options are supported with vSphere 6.x? (Choose two.)___
A. Single-Initiator
B. Single-Initiator-Single-Target
C. Multiple-Initiators-Single-Target
D. Multiple-Initiators-Multiple-Targets
【多选题】
An administrator is attempting to remove an ESXi 6.x host from a vSphere Distributed Switch (vDS). When the administrator attempts to remove the host, the following error is observed: <The resource '16' is still in use.> What three steps are needed to successfully remove the host from the switch? (Choose three.)___
A. Select Manage Ports on the vDS for the host.
B. Locate all ports currently in use on the vDS for the host.
C. Migrate or delete any vmkernel or virtual machine adapters associated with the switch.
D. Remove all network cards from the switch before trying to remove the host.
E. Create a standard switch for everything to be automatically be migrated to.
