【判断题】
泡沫比例混合系统分负压式和正压式二类,其中压缩空气泡沫系统(CAPS)属正压式。
A. 对
B. 错
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【判断题】
照明消防车车载灯具为特种灯具,体积小,内温高,故照明电器系统不能在大风大雨环境中使用。
A. 对
B. 错
【判断题】
分水器阀门应开启灵活,无卡阻现象,最大开启力不得大于300N。
A. 对
B. 错
【判断题】
安全钩长期保存时,应涂上黄油,以免锈蚀;金属件腐蚀或老化时应按厂方使用说明中的规定进行处理。
A. 对
B. 错
【判断题】
安全钩使用后,擦拭干净,放置于潮湿清洁处备用。
A. 对
B. 错
【判断题】
若安全绳未能通过检查或其安全性出现问题,应更换安全绳并将旧绳报废。
A. 对
B. 错
【判断题】
贮存救援靴时,应避免阳光直射、雨淋及受潮,可以与酸碱、油及有腐蚀性物品放在一起。
A. 对
B. 错
【判断题】
压缩空气泡沫消防车,是指装置了压缩空气A类泡沫系统(CAFS)的消防车。
A. 对
B. 错
【判断题】
起动手抬机动消防泵时应先用脚踩稳框架并迅速地用力拉动起动绳,起动汽油机,然后按压化油器上的油锨,待汽油从通气孔处溢出少许后即松开。
A. 对
B. 错
【判断题】
消防员灭火防护胶靴每次穿着后应用清水冲洗,洗净后放在阴凉、通风处晾干,直接日晒。
A. 对
B. 错
【判断题】
消防员灭火防护胶靴采用多层结构设计,主体颜色为黄色,配以灰色的围条、沿条等。
A. 对
B. 错
【判断题】
水气比指产生泡沫时,混合液中水的体积与空气的体积比。
A. 对
B. 错
【判断题】
干泡沫指系统泡沫液混合比为0.3~1%时,喷出的空气含量大、流动性差和附着力强的泡沫。通常呈成雪花状,泡沫析水时间长,能够在垂直表面上长时间停留。
A. 对
B. 错
【判断题】
不准将30MPa压力的气瓶连接最高输入20MPa压力的减压器上。
A. 对
B. 错
【判断题】
湿泡沫指系统泡沫液混合比为0.3~1%时,喷出的空气含量小、流动性好和附着力较差的泡沫,通常呈普通泡沫状,泡沫析水时间短,通常在垂直表面不能形成堆积厚度。
A. 对
B. 错
【判断题】
中等泡沫指当系统泡沫液混合比为0.3~1%时,喷出的空气含量介于干泡沫和湿泡沫之间,流动性较差、附着力较强的泡沫,通常呈絮状,泡沫析水时间较长,能够附着在建筑物或其它物体表面上。
A. 对
B. 错
【判断题】
消防员隔热防护服的款式为分体式隔热服和连体式隔热服两种。
A. 对
B. 错
【判断题】
消防手套按防护要求分为将其分为一类、二类和三类,一类手套防护等级最高。
A. 对
B. 错
【判断题】
标准规定消防员灭火防护胶靴应具有耐电压性能,可用于带电场所、不得用于浓酸和浓碱等强烈腐蚀性化学品存在的场所。
A. 对
B. 错
【判断题】
消防员隔热防护服应及时清洗、擦净、晾干。隔热层和外层不可分开清洗。
A. 对
B. 错
【判断题】
消防头盔由帽壳、佩戴装置、面罩、披肩和下颏带等主要部件组成。
A. 对
B. 错
【判断题】
消防头盔的外形可分为无帽沿式和有帽沿式两种。
A. 对
B. 错
【判断题】
腰斧受一般性沾污时,可先用肥皂水擦洗,再用水清洗后凉干;当腰斧受油漆或柏油等玷污时,应先用四氯化碳擦去污痕迹,再按以上方法清洗,切忌用汽油或石蜡油等进行擦洗,以免橡胶柄套损坏。
A. 对
B. 错
【判断题】
消防员配备使用的消防员呼救、定位器具包括消防员呼救器和方位灯。
A. 对
B. 错
【判断题】
固态微型强光防爆电筒灯具内部电路设计具有防止过充、过放、短路保护装置及开关防误操作功能。
A. 对
B. 错
【判断题】
固态微型强光防爆电筒由灯头、壳体和灯尾等部件组成。
A. 对
B. 错
【判断题】
便携式强光防爆工作灯强光与工作光可任意转换,焦距可调。
A. 对
B. 错
【判断题】
便携式强光防爆工作灯主要由灯头、腰带夹、电池盒等部件组成。
A. 对
B. 错
【判断题】
消防员灭火防护皮靴靴面材料有阻燃性能。
A. 对
B. 错
【判断题】
消防安全带可调节尺寸大小以适合体型佩戴。
A. 对
B. 错
【判断题】
正压式空气呼吸器不属于个人防护装备。
A. 对
B. 错
【判断题】
供气消防车充气泵首次使用累计500h后要彻底更换机油。
A. 对
B. 错
【判断题】
手提式防爆强光照明灯不具备防水性能。
A. 对
B. 错
【判断题】
灭火防护服洗涤过程中水温不可高于35℃。
A. 对
B. 错
【判断题】
防化防核服在污染区域用过后经清洗可反复使用。
A. 对
B. 错
【判断题】
空气呼吸器警报器报警压力为15MPa。
A. 对
B. 错
【判断题】
空气呼吸器最高工作压力为60MPa。
A. 对
B. 错
【判断题】
灭火防护服使用年限一般为15年。
A. 对
B. 错
【判断题】
液压控制阀分为:方向控制阀、压力控制阀、流量控制阀、速度控制阀。
A. 对
B. 错
【判断题】
BG40/30,40代表最高压力,30代表最高压力时出水流量。
A. 对
B. 错
【判断题】
BD40泵是属于高压泵。
A. 对
B. 错
推荐试题
【判断题】
液压元件中液压泵、液压马达与电动机、工作机构轴线间的倾角偏差不大于40´
A. 对
B. 错
【判断题】
用经纬仪和平行光管测量机床转台分度误差时,应用专用心轴配装在转台中心孔中将经纬仪和心轴紧固联接在一起
A. 对
B. 错
【判断题】
减少更换刀具、对刀、试切时间,也可以减少辅助时间
A. 对
B. 错
【判断题】
班组的经济核算无论是项目承包或单台总工时的考核,还是按计划,经济地完成任务,都需要以降低成本,提高质量,缩短修理周期为班组的生产目标
A. 对
B. 错
【判断题】
电源供给异常会导致电磁离合器烧坏
A. 对
B. 错
【判断题】
轴承预紧的目的是提高轴承支承的刚度,提高轴的旋转精度,降低轴的震动和噪声,降低轴之间的摩擦
A. 对
B. 错
【判断题】
经纬仪光学对中误差一般应小于1mm
A. 对
B. 错
【判断题】
转子材质的不均匀将会影响高速机械转子精度
A. 对
B. 错
【判断题】
镦粗加工工艺最好用于塑性好,延展性大的金属材料台阶轴或双联齿轮等毛坯件加工
A. 对
B. 错
【判断题】
为了保证大型设备基础的承载能力,一般采用钢筋温凝土整体浇灌的结构
A. 对
B. 错
【判断题】
多段床身接合面刮削时,将被刮的接合面端用枕木垫高的目的是便于刮研
A. 对
B. 错
【判断题】
更换清单,由主管工艺人员提出,由备件人员核定出价格,更换件包括机械,电器,液(气)压的备配件和外购件
A. 对
B. 错
【判断题】
任何提高劳动生产率的措施,都必须以经济效益为前提
A. 对
B. 错
【判断题】
精密机床导轨在的粗糙度要求是:每25mm×25mm在16~20点
A. 对
B. 错
【判断题】
工作台要牢固平稳,平台周围要保持整洁,通行要方便,1米内禁止堆放物件
A. 对
B. 错
【判断题】
两孔轴线相交成 90°角,一个孔直径为φ20mm,另一个孔直径是φ30mm,应该先钻穿直径大的孔
A. 对
B. 错
【判断题】
碳素工具钢和合金工具钢用于制造中、低速成型刀具
A. 对
B. 错
【判断题】
经纬仪整平时,经反复调整,直到仪器转到任意位置时,水准气泡最大偏离值小于二分之一格为止
A. 对
B. 错
【判断题】
刮削大型机床导轨面时,应在将导轨面上的零件全部拆除后进行,以保证刮削质量
A. 对
B. 错
【判断题】
要安排好培训计划,做好上课的准备工作,做到有组织,有计划地进行培训,做到定时间,定地点,定内容,定进度,定要求,有练习,有考核
A. 对
B. 错
【判断题】
轨道制作主要是轨道调直和接头,调直后对轨道进行编号,两条轨道上从端部或伸缩缝处算起,轨道接头至少要对齐,以使运转平稳
A. 对
B. 错
【判断题】
为实现电动机连续正转运行需采用具有接触器自锁的控制线路和手动正转控制回路
A. 对
B. 错
【判断题】
在修理带传动机构时,发现带轮孔超差额0.08mm,造成配合过松,一般可用镀铬法来加大轴颈尺寸
A. 对
B. 错
【判断题】
用经纬仪和平行光管测量机床转台分度误差时,应用专用心轴配装在转台中心孔中将经纬仪和心轴紧固联接在一起
A. 对
B. 错
【判断题】
采用双螺母螺纹式调整滚珠丝杠轴向间隙的方法结构紧凑,调整方便,应用广泛
A. 对
B. 错
【判断题】
若自准直仪上读数鼓轮每格角值分度值为1",则其线值分度值可用0.05mm/m表示
A. 对
B. 错
【判断题】
所有的紫色酒精,在 1 米内不准点有明火,不准放在暖气片上
A. 对
B. 错
【判断题】
固定式装配适用于单件和小批量模具的装配,以及装配精度要求较高,需要调整的部位较多的装配
A. 对
B. 错
【判断题】
我国对企业发生的事故,坚持“四不放过”原则进行处理
A. 对
B. 错
【判断题】
齿轮的齿侧间隙分为12 个等级
A. 对
B. 错
【判断题】
在机械设备中,凸轮表面误差将会引起扭转振动
A. 对
B. 错
【单选题】
What happens to the status of users already logged into ESXi Shell when a vSphere administrator enables lockdown mode?___
A. Users remain logged in and can run commands, except to disable lockdown mode.
B. Users remain logged in and can run commands, including disabling lockdown mode.
C. Users are immediately logged out of ESXi Shell.
D. Users are logged out after a timeout specified by the vSphere administrator.
【单选题】
What is the effective vSphere licensing level during the 60 day evaluation period?___
A. vSphere Foundation Essentials Plus
B. vSphere Standard
C. vSphere Enterprise
D. vSphere
E. nterprise Plus
【单选题】
To comply with security requirements, an administrator with a vCenter Server Appliance needs to force logoff of the vSphere web client after 10 minutes of inactivity.What should the administrator do to meet the requirement?___
A. Edit: /var/lib/vmware/vsphere-client/webclient.properties, modify session.timeout=10
B. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=600
C. Edit: /var/lib/vmware/vsphere-client/webclient.properties modify session.timeout=600
D. Edit: /opt/vmware/vsphere-client/webclient.properties, modify session.timeout=10
【单选题】
An administrator enables High Availability (HA) on a Virtual SAN cluster.Which network is used for HA Network Heatbeat configuration?___
A. The Management network.
B. The vMotion network.
C. The Virtual SAN network.
D. The Provisioning Traffic network.
【单选题】
A user wants to monitor a business-critical virtual machine to ensure that it doesn't run out of resources. What metric could be monitored in vRealize Operations to address this concern?___
A. Time Remaining badge
B. Compliance badge
C. Reclaimable Waste badge
D. Density badge
【单选题】
An administrator has recently installed a new ESXi 6.x Host, and during the configuration notices sporadic network problems. To check whether the issue occurred sometime during the configuration, the administrator would like to reset the system.How can this be accomplished in the shortest amount of time?___
A. Run the ESXi installer again and reinstall the host.
B. Select the Reset System Configuration option from the vSphere Client when connected directly to the host.
C. From the
D. irect Console User Interface, select Reset System Configuration.
【单选题】
A vApp is running out of compute resources when overall activity is high within the resource pool. At other times, everything is fine.What should be done to resolve this issue?___
A. Increase the size of the resource pool Shares.
B. Set the vApp's CPU and Memory Reservation Type to Expandable.
C. Set the vApp's CPU and Memory Limit to Unlimited.
D. Create a new resource pool with the existing hardware configuration.
【单选题】
A virtual machine has been renamed and an administrator is unable to find files with the new virtual machine name in the datastore.What is the reason for this?___
A. The names of the files on the datastore do not change.
B. The names of the files on the datastore have been corrupted.
C. The virtual machine needs to be re-added to the inventory.
D. The Distributed Resource Scheduler moved the virtual machine to another host.
【单选题】
An administrator has configured network connectivity for a new virtual machine, as shown in the Exhibit.What will occur with the network traffic of this virtual machine when communicating externally from vSwitch1?___
A. The virtual machine will communicate on both uplinks
B. The virtual machine will only communicate on vmnic1
C. The virtual machine will only communicate on vmnic2
D. The virtual machine will fail to communicate externally